-
Bunn 4 - page 1
IMIX-3 IMIX-4 IMIX-5 INST ALLA TION & OPERA TING MANUAL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 37510.0000D 01/06 ©2004 Bunn-O-Matic Corporation www .bunnomatic.com ...
-
Bunn 4 - page 2
2 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specifi ed below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years parts and 1 year ...
-
Bunn 4 - page 3
3 W ARNING ! Fill water tank before turning - on - thermostat or connecting appliance to power source. Use only on a properly protected circuit capable of the rated load. Electrically ground the chassis. Follow national/local electrical codes. Do not use near combustibles. F AILURE TO COMPL Y RISKS EQUIPMENT DAMAGE, FIRE, OR SHOCK HAZARD READ THE E ...
-
Bunn 4 - page 4
4 INITIAL SET -UP 1. Apply the four non-skid pads from the parts box to the bottom of the legs. 2. Remove the drip tray assembly , drip tray bracket, and splash panel assembly from the parts box. 3. Place a set of key holes in the drip tray bracket over the lower two screws in the panel below the hopper access door; push down gently and tighten scr ...
-
Bunn 4 - page 5
5 INITIAL fi ll & heat 1. T urn on the water supply and connect the dispenser to the power source. 2. Water will automatically fl ow into the tank to the proper level and then shut-off. This will take less than ten minutes. 3. When the tank is full of water , open the front door and place the ON/OFF/NIGHT switch in the “ON” (up- per) posi ...
-
Bunn 4 - page 6
6 HOPPER DISPENSE RA TE OF PRODUCT The hopper dispense rates are preset at the factory . With 22 tooth gear and auger wire, the preset dispense rate is approximately 3 to 5 grams per second. With 30 tooth gear and auger wire, the preset dispense rate is approximately 5 to 7 grams per second. The hopper dispense rates can be individually programmed ...
-
Bunn 4 - page 7
7 Adjust tank temperature (190° F maximum) Adjust minimum tank ready temper - ature for lockout (185° maximum) Adjust hopper motor speed for station selected T ANK TEMP XXX° (-) EXIT (+) READY TEMP XXX° (-) EXIT (+) DRINK STRENGTH (-) XX (+) XX° CAL XX° (-) T ank T emp (+) 235 REFILL 155 (-) EXIT (+) CAL WA TER ? PRESS DISPENSE Calibrate temp ...
-
Bunn 4 - page 8
8 A. Enter program mode and advance to next menu B. Incriment display value positive C. Exit program mode D. Incriment display value negative E. Return to previous menu and interrupt dispense PORTION CONTROL MODELS D igital B everage C ontr ol D igital B everage C ontr ol ST OP PROGRAM HOME SCREEN The screen above will be shown when the dispenser i ...
-
Bunn 4 - page 9
9 PROGRAMMING CUP SIZES - Portion Control Models The cup size can be programmed in portion control models by “EXAMPLE” or “TIME”. Programming by EXAMPLE is manually pressing desired dispense button, then releasing when the desired cup size is attained. The time required to fi ll the cup will be stored in the controller memory when moving t ...
-
Bunn 4 - page 10
10 DISABLE MESSAGES ? NO EXIT YES Press and release right switch (advance to next menu), “T ANK TEMP XXX°” appears on screen. PROGRAMMING THE DISPENSER (cont.) T ANK TEMP XXX° READY TEMP XXX° (-) EXIT (+) STRENGTH ADJ. ? (-) EXIT (+) EXIT YES ENTER P ASSWORD (-) XXXX (+) CALIBRA TION ? EXIT YES LOCKS/DISABLES ? EXIT YES AUDIBLE ALARM ? NO EX ...
-
Bunn 4 - page 11
11 XX° CAL XX° (-) T ank T emp (+) PROGRAMMING THE DISPENSER (cont.) DRINK STRENGTH 1 (-) XX (+) PRESS DISPENSE TO CHECK T ASTE T ASTE 1 OK ? NO YES SET FLA VOR 1 BY T ASTE RECIPE ENTER RECIPE # #.# gm/fl uid oz CHANGING V ALUES WILL EFFECT RPM ARE YOU SURE ? NO EXIT YES (B) Adjust hopper motor speed for station for station selected SELECT UNITS ...
-
Bunn 4 - page 12
12 PROGRAMMING THE DISPENSER (cont.) LOW POWDER LOCK ? NO EXIT YES DISPENSE LOCKOUT NO EXIT YES RINSE ALARM ? NO EXIT YES HEAD 1 DISABLE ? NO EXIT YES SET P ASSWORD ? (-) XXXX (+) Returns to (G) (page 10) TEST SWITCHES ? Use Switch T o T est TEST HEA TER ? EXIT YES TEST REFILL ? EXIT YES TEST HOT WA TER ? EXIT YES TEST AUGERS ? DISPENSE TO TEST TES ...
-
Bunn 4 - page 13
13 $Ú"5../-! 4)##/20/2!4)/. 6/, 43!#7)2% 6/, 43!#7)2% 3).',%0(!3%(: 3#(%-! 4)#7)2).'$)! '2!- I-) 8 '2. , ",+ ...
-
Bunn 4 - page 14
14 "Ú"5../-! 4)##/20/2!4)/. 6/, 43!#7)2% 6/, 43!#7)2% 3).',%0(!3%(: 3#(%-! 4)#7)2).'$)! '2!- I-) 8 I-) 8 &a ...
-
Bunn 4 - page 15
15 37510 010206 "Ú"5../-! 4)##/20/2!4)/. 6/, 43!#7)2% 3).',%0(!3%(: SCHEMA TIC WIRING DIAGRAM IMIX-3A '2. , ",+ ",+ ",+ ",+ ",+ ,)-)4 4(%2-/34 ...
-
Bunn 4 - page 16
16 37510 010206 "Ú"5../-! 4)##/20/2!4)/. 6/, 43!#7)2% 3).',%0(!3%(: SCHEMA TIC WIRING DIAGRAM IMIXA-4/IMIXA-5 '2. , ",+ ",+ ",+ ",+ ",+ " ...
Avez-vous une question à propos de Bunn 4?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Bunn 4, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Bunn 4 il est probable qu’il a envie de partager la façon de le résoudre.