Manuel d’utilisation KTI Networks KCD-400 Series

26 pages 1.39 mb
Télécharger

Aller à la page of 26

Summary
  • KTI Networks KCD-400 Series - page 1

    -1- INDUSTRIAL 1000BASE-T TO 1000BASE-X MEDIA CONVERTERS KCD-400 Series Installation Guide DOC.060227-KCD-400 ...

  • KTI Networks KCD-400 Series - page 2

    -2- (C) 2005 KTI Networks Inc. All rights reserved. No part of this documen- tation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without per- mission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from ...

  • KTI Networks KCD-400 Series - page 3

    -3- The information contained in this document is subject to change without prior notice. Copyright (C) All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. FCC NOTICE This device complies with Class B Part 15 the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful inte ...

  • KTI Networks KCD-400 Series - page 4

    -4- T a ble of Contents 1. Introduction ......................................................... 5 1.1 Features ........................................................................................ 6 1.2 Specifications ................................................................................ 7 1.3 Special Functions ...................... ...

  • KTI Networks KCD-400 Series - page 5

    -5- 1. Introduction The industrial 1000BASE-T to 1000BASE-X media converter series pro- vides industrial strength Ethernet copper-to-fiber media conversion, allow- ing for 1000Base-T-to-1000Base-X over multi-mode or optional single- mode fiber optical media. For industrial environment, the converters are designed with the follow- ing enhanced featu ...

  • KTI Networks KCD-400 Series - page 6

    -6- 1.1 Features • Gigabit copper to fiber conversion: 1000Base-T-to-1000Base-SX/LX over multimode or single-mode fiber • SFP design : For flexibility , a n SFP (Mini-GBIC) connector is provided for the fiber port to accommodate any type of SFP fiber transceiver when needed. • Support full wire speed copper to fiber conversion • Auto MDI/MD ...

  • KTI Networks KCD-400 Series - page 7

    -7- 1.2 Specifications This figure shows the important components of the converter: ...

  • KTI Networks KCD-400 Series - page 8

    -8- T wisted-Pair Interfa ce (Copper Por t) Connector Shielded RJ-45 Signal Compliance IEEE 802.3ab 1000BASE-T std. Pin Assignments Auto MDI/MDI-X detection Data Speed 1000Mbps Duplex Mode Half-duplex or Full-duplex Configuration Auto-negotiation support Ca ble T ypes Category 5 or higher UTP Link Distance Up to 100 meters Fiber Optic Interface (Fi ...

  • KTI Networks KCD-400 Series - page 9

    -9- DC Power Interface Interface Screw-type terminal block 1. T wo pairs for power wire ca sca ding 2. One pair for power failure relay output DC Jack (-D6.3mm/+D2.0mm) Operating Input V oltages +7V ~ +30V(+5%) Power c on s um ption 2.25W @+7.5VDC input 2.3W @+24VDC input 2.5W @+30VDC input Basic Information Conversion Full wire speed 1000Mbps - 1, ...

  • KTI Networks KCD-400 Series - page 10

    -10- Certificate F C C Part 15 Class B CE/EMC EMI EN50081-1 Class B EMS EN55024 CE/L V D Safe ty E N 60950 EN 50081-1/1992 : EN55022:1994/A1:1995/A2:1997 EN61000-3-2:2000 EN61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001 IEC 61000-4-2:1995 ESD T est IEC 61000-4-3:1995 RS T est IEC 61000-4-4:1995 EFT/BURST T est IEC 61000-4-5:1995 Surge T est IEC 61000 ...

  • KTI Networks KCD-400 Series - page 11

    -11- 1.3 Special Functions Auto MDI/MDI-X Function This function allows the copper port to auto-detect the twisted-pair sig- nals and adapts itself to form a valid MDI to MDI-X connection with the remote connected device automatically . Link Fault Pass Through Function When a link fault is detected on the copper port, the device will force a link d ...

  • KTI Networks KCD-400 Series - page 12

    -12- Far End Fault Function The fiber port is facilitated with this function. When the fiber port detects a link failure on its receiving circuitry , it will send out a n FEFI (Far End Fault Indication) signal to the remote connected device to indicate a remote fault is detected. It also is capable to receive FEFI signal sent from the remote link p ...

  • KTI Networks KCD-400 Series - page 13

    -13- 2. Installation 2.1 Unpacking Check that the following components have been included: • Information CD • The Media Converter unit • DIN-rail mounting bracket If any item is found missing or damaged, please contact your local reseller for replacement. The following are available optional accessories: • Panel Mounting Bracket The bracket ...

  • KTI Networks KCD-400 Series - page 14

    -14- 2.2 Safety Cautions T o reduce the risk of bodily injury , electrical shock, fire, a nd da mage to the equipment, observe the following precautions. • Do not service any product except as explained in your system documentation. • Opening or removing covers may expose you to electrical shock. Only a trained service technician should service ...

  • KTI Networks KCD-400 Series - page 15

    -15- 2.3 DIN-Rail Mounting In the product package, a DIN-rail bracket is installed on the device for mounting the converter in a industrial DIN-rail enclosure. The steps to mount the device onto a DIN rail are: 1 . Install the mounting bracket onto the device unit as shown below: 2 . Attach bracket to the lower edge of the DIN rail and push the uni ...

  • KTI Networks KCD-400 Series - page 16

    -16- The final mechanical dimensions after installing DIN rail mounting bracket are: ...

  • KTI Networks KCD-400 Series - page 17

    -17- 2.4 Panel Mounting The device is provided with an optional panel mounting bracket. The bra cket support mounting the device on a pla ne surfa ce securely . The mounting steps are: 1 . Install the mounting bracket on the device unit. 2 . Screw the bracket on the device unit. 3 . Screw the device unit on a panel. 4 . Make sure that there are pro ...

  • KTI Networks KCD-400 Series - page 18

    -18- The screw locations and final dimension are shown below: ...

  • KTI Networks KCD-400 Series - page 19

    -19- 2.5 Applying Power The power specifications of the device are: Operating V oltage + 7 ~ +30VDC Power Consumption Max. 2.5W @30VDC The device provides two types of power interfaces, terminal block and DC power ja ck for rece iving DC power input from external power supply . Using T erminal Blocks Either DC1 interface or DC2 interface can be use ...

  • KTI Networks KCD-400 Series - page 20

    -20- Power wires: 24 ~ 12A W G (IEC 0.5~2.5mm 2 ) Install the power source wires with the plug properly . Screw the wire with plug securely . Then, plug in DC1 conta cts. If cascading the power to next device is needed, install the power wires and plug for another switch. Then, use DC2 contacts. Note: Only up to four device units can be cascaded to ...

  • KTI Networks KCD-400 Series - page 21

    -21- Using DC Power Jack DC Jack Connector: Jack D 6.3mm D 2.0mm AC Power Adapters: Optional commercial rated adapters are available for purchasing. Rated AC120V/60Hz DC7.5V 1A Rated AC230V/50Hz DC7.5V 1A Rated AC100V/50-60Hz DC7.5V 1A Rated AC240V/50Hz DC7.5V 1A Connect power adapter DC plug to the DC power jack of the converter before connecting ...

  • KTI Networks KCD-400 Series - page 22

    -22- 2.6 Power Failure Relay Output The device provides a relay output to report power failure event to a remote alarm monitoring system. The replay output is provided with two contacts labeled PF+ and PF- in the terminal block interface. Use the provided 2P terminal plug for signal wiring and plug into the PF+/ - contacts. The function is designed ...

  • KTI Networks KCD-400 Series - page 23

    -23- 2.7 Ma king T wisted Pair Copper Port Conne ction Copper port is featured to support connection to : • Auto-negotiation devices • Auto-negotiation incapable 10BASE-T devices • Auto-negotiation incapable 100BASE-TX devices Network Cables 1000BASE-T : 4-pair UTP Cat. 5e or 6, EIA/TIA-568B 100-ohm STP Link distance: Up to 100 meters Note: T ...

  • KTI Networks KCD-400 Series - page 24

    -24- 2.8 Making Fiber Port Connection The mini-GBIC (SFP) port must be installed with an SFP fiber trans- ceiver for making fiber connection. The device may come with an SFP tra nsceiver pre-installed when it is shi pped from factory . Installing SFP Fiber T ra nsceiver Turn off the power to the device. Insert the SFP fiber transceiver into the min ...

  • KTI Networks KCD-400 Series - page 25

    -25- 3 LED Indicators The following figure shows the locations of the configuration switches and LED indicators: 3.1 LED Indicators LED DISPLA Y ST A TE INTERPRET A TION P W R Power status O N The device is powered on. O F F The device is powered off. S F P SFP slot status O N An SFP transceiver is installed. O F F No SFP transceiver is installed. ...

  • KTI Networks KCD-400 Series - page 26

    -26- Appendix: Model Optical Specifications The media converter series provides the following fiber options: Model Specifications Reference Operating KCD-400-xx FX W avelength Fiber Dista nce T e mpera tur e -SX L C 850nm 50/125 MMF 500m -20 ~ 70 o C 62.5/125 MMF 200m - LX L C 1310nm MMF 550m -20 ~ 70 o C SMF 10km -LX20 L C 1310nm SMF 20km -20 ~ 70 ...

Fabricant KTI Networks Catégorie Network Card

Les documents que nous recevons du fabricant de l'appareilKTI Networks KCD-400 Series peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques KTI Networks
- manuels d’utilisations KCD-400 Series
- fiches produit KTI Networks
- dépliants
- ou étiquettes-énergie KTI Networks KCD-400 Series
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation KTI Networks KCD-400 Series.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation KTI Networks KCD-400 Series, manuels d’entretien, brefs manuels ou manuels de l’utilisateur KTI Networks KCD-400 Series. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit KTI Networks KCD-400 Series.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil KTI Networks KCD-400 Series, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser KTI Networks KCD-400 Series par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs KTI Networks KCD-400 Series.

Le manuel d’utilisation complet KTI Networks, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel KTI Networks KCD-400 Series - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières KTI Networks KCD-400 Series, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lKTI Networks KCD-400 Series qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil KTI Networks KCD-400 Series - qui devraient nous aider dans les premières étapes lors de l'utilisation KTI Networks KCD-400 Series
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de KTI Networks KCD-400 Series
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service KTI Networks KCD-400 Series dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de KTI Networks KCD-400 Series?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec KTI Networks KCD-400 Series, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec KTI Networks KCD-400 Series il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)