Français dropdown-ico

Manuel d’utilisation Directed Electronics K10

16 pages 0.66 mb
Télécharger

Aller à la page of 16

Summary
  • Directed Electronics K10 - page 1

    NO TE: This product is intended for installation b y a prof essional installer only! Any attempt to install this product by an y person other than a trained prof essional may result in se v ere damage to a vehicle’ s electrical system and components. Model K10 installation guide ...

  • Directed Electronics K10 - page 2

    3 table of contents primary harness (H1) wire connection guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 primary har ness (H1) wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 primary har ness wire descriptions . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Directed Electronics K10 - page 3

    4 primary harness (H1) wire connection guide primary harness (H1) wiring diagram The primar y harness supplied with this unit is the standard 12-pin harness used. T wo wires in the plug are not used. The upgrade from this unit to a security system would simply require unplugging and exchanging control units and connecting the necessar y wires to th ...

  • Directed Electronics K10 - page 4

    5 H1/2 WHITE (-) Parking Light Output This wire provides a (-) 200mA output to flash the parking lights. This is suitable for driving (-) light control wires in T oyota, Lexus, BMW , some Mitsubishi, some Mazda, etc. If the vehicle has a positive parking light circuit, a relay must be used to flash the parking lights. H1/3 WHITE/BLUE (-) Channel 3 ...

  • Directed Electronics K10 - page 5

    6 H1/6 BLUE (-) 200 mA Second Unlock Output The H1/6 BLUE output is used for progressive unlock. A progressive unlock system unlocks the driver's door when the unlock (disarm) button is pressed and unlocks the passenger doors if the unlock (disarm) button is pressed again within 15 seconds after unlocking the driver's door . The BLUE wire ...

  • Directed Electronics K10 - page 6

    7 H1/11 RED (+)12V constant power input Before connecting this wire, remove the supplied fuse. Connect to the positive batter y terminal or the constant 12V supply to the ignition switch. N N O O T T E E : : Always use a fuse within 12 inches of the point you obtain (+)12V . Do not use the fuse in the har- ness for this purpose. This fuse protects ...

  • Directed Electronics K10 - page 7

    8 door lock harness (H4), wire connection guide ___ ___ ___ peripheral plug-in harnesses LED, 2-pin WHITE plug The LED operates at (+) 2 volt DC and plugs into the two-pin WHITE port. Make sure the LED wires are not shorted to ground as the LED will be damaged. Multiple LED’ s can be used, but they must be wired in series. The LED fits into a 9/3 ...

  • Directed Electronics K10 - page 8

    9 Pro Security Pr ogrammer interface, 3-pin port The BLACK three-pin port is provided for pr ogramming of the unit. When using the P ro Security P rogrammer , it is possible to configure any and all of the programmable functions. F or more information please refer to the guide packaged with the programmer . module programming The System Features Le ...

  • Directed Electronics K10 - page 9

    10 3. T ransmit. The transmitter is used to select the desired setting. As shipped, the unit is configured to the LED ON settings. These are the default settings. Pressing the lock button will set it to the LED ON setting. The LED will light solid (stop flashing) to indi- cate the setting. The horn will honk once (if connected). Pressing the unlock ...

  • Directed Electronics K10 - page 10

    11 system features menus feature descriptions 1 ACTIVE/P ASSIVE ARMING: When active arming is selected, the starter kill will ar m (if connected) only when the transmitter is used. When set to passive arming, the starter kill will ar m (if connected) 30 seconds after the ignition key is turned off. 2 CHIRPS ON/OFF: This feature controls the chirps ...

  • Directed Electronics K10 - page 11

    12 8 DOUBLE PULSE UNLOCK OFF/ON: Some vehicles require two pulses on a single wire to unlock the doors. When the double pulse unlock feature is turned on, the BLUE H2/C wire will supply two nega- tive pulses instead of a single pulse. At the same time, the GREEN H2/A wire will supply two positive pulses instead of a single pulse. This makes it poss ...

  • Directed Electronics K10 - page 12

    13 Channels #4-6: Channels 4 through 6 are used to assign the arm, disarm and panic functions to sep- arate buttons on the remote control. T eaching a button to Channel 4 erases all information about that remote from memor y . Any auxiliar y functions that are desired will have to be reprogrammed. Similarly , if the remote is set up to use the sepa ...

  • Directed Electronics K10 - page 13

    14 remote configurations The transmitters can be programmed with the standard or single button arm/disarm configurations by using the Auto Learn functions in the Remote Coding. standard configuration A remote that uses the standard configuration operates similarly to many factor y keyless entry remotes. A standard configuration remote allows arming ...

  • Directed Electronics K10 - page 14

    15 power-up Power-up ensures that the when the system is powered up it will return to the same state it was in when power is disconnected. For a full description of power-up refer to the owner's manual. ...

  • Directed Electronics K10 - page 15

    16 3-Pin 2-Wire Door Lock Harness Override Switch Pro Secur ity Programmer ® ™ wiring quick reference guide ...

  • Directed Electronics K10 - page 16

    Get Started Get Protected Ungo Pro Security 661 W . Redondo Beach Blvd. Gardena, Ca. 90247 800-GO-CLARION © 2003 Directed Electroni cs, Inc . - All rights r eserved GK10 11-03 ...

Fabricant Directed Electronics Catégorie Network Card

Les documents que nous recevons du fabricant de l'appareilDirected Electronics K10 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Directed Electronics
- manuels d’utilisations K10
- fiches produit Directed Electronics
- dépliants
- ou étiquettes-énergie Directed Electronics K10
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Directed Electronics K10.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Directed Electronics K10, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Directed Electronics K10. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Directed Electronics K10.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Directed Electronics K10, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Directed Electronics K10 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Directed Electronics K10.

Le manuel d’utilisation complet Directed Electronics, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Directed Electronics K10 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Directed Electronics K10, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lDirected Electronics K10 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Directed Electronics K10 - qui devraient nous aider dans les premières étapes lors de l'utilisation Directed Electronics K10
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Directed Electronics K10
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Directed Electronics K10 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Directed Electronics K10?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Directed Electronics K10, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Directed Electronics K10 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)