Directed Electronics K10の取扱説明書

16ページ 0.66 mb
ダウンロード

ページに移動 of 16

Summary
  • Directed Electronics K10 - page 1

    NO TE: This product is intended for installation b y a prof essional installer only! Any attempt to install this product by an y person other than a trained prof essional may result in se v ere damage to a vehicle’ s electrical system and components. Model K10 installation guide ...

  • Directed Electronics K10 - page 2

    3 table of contents primary harness (H1) wire connection guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 primary har ness (H1) wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 primary har ness wire descriptions . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Directed Electronics K10 - page 3

    4 primary harness (H1) wire connection guide primary harness (H1) wiring diagram The primar y harness supplied with this unit is the standard 12-pin harness used. T wo wires in the plug are not used. The upgrade from this unit to a security system would simply require unplugging and exchanging control units and connecting the necessar y wires to th ...

  • Directed Electronics K10 - page 4

    5 H1/2 WHITE (-) Parking Light Output This wire provides a (-) 200mA output to flash the parking lights. This is suitable for driving (-) light control wires in T oyota, Lexus, BMW , some Mitsubishi, some Mazda, etc. If the vehicle has a positive parking light circuit, a relay must be used to flash the parking lights. H1/3 WHITE/BLUE (-) Channel 3 ...

  • Directed Electronics K10 - page 5

    6 H1/6 BLUE (-) 200 mA Second Unlock Output The H1/6 BLUE output is used for progressive unlock. A progressive unlock system unlocks the driver's door when the unlock (disarm) button is pressed and unlocks the passenger doors if the unlock (disarm) button is pressed again within 15 seconds after unlocking the driver's door . The BLUE wire ...

  • Directed Electronics K10 - page 6

    7 H1/11 RED (+)12V constant power input Before connecting this wire, remove the supplied fuse. Connect to the positive batter y terminal or the constant 12V supply to the ignition switch. N N O O T T E E : : Always use a fuse within 12 inches of the point you obtain (+)12V . Do not use the fuse in the har- ness for this purpose. This fuse protects ...

  • Directed Electronics K10 - page 7

    8 door lock harness (H4), wire connection guide ___ ___ ___ peripheral plug-in harnesses LED, 2-pin WHITE plug The LED operates at (+) 2 volt DC and plugs into the two-pin WHITE port. Make sure the LED wires are not shorted to ground as the LED will be damaged. Multiple LED’ s can be used, but they must be wired in series. The LED fits into a 9/3 ...

  • Directed Electronics K10 - page 8

    9 Pro Security Pr ogrammer interface, 3-pin port The BLACK three-pin port is provided for pr ogramming of the unit. When using the P ro Security P rogrammer , it is possible to configure any and all of the programmable functions. F or more information please refer to the guide packaged with the programmer . module programming The System Features Le ...

  • Directed Electronics K10 - page 9

    10 3. T ransmit. The transmitter is used to select the desired setting. As shipped, the unit is configured to the LED ON settings. These are the default settings. Pressing the lock button will set it to the LED ON setting. The LED will light solid (stop flashing) to indi- cate the setting. The horn will honk once (if connected). Pressing the unlock ...

  • Directed Electronics K10 - page 10

    11 system features menus feature descriptions 1 ACTIVE/P ASSIVE ARMING: When active arming is selected, the starter kill will ar m (if connected) only when the transmitter is used. When set to passive arming, the starter kill will ar m (if connected) 30 seconds after the ignition key is turned off. 2 CHIRPS ON/OFF: This feature controls the chirps ...

  • Directed Electronics K10 - page 11

    12 8 DOUBLE PULSE UNLOCK OFF/ON: Some vehicles require two pulses on a single wire to unlock the doors. When the double pulse unlock feature is turned on, the BLUE H2/C wire will supply two nega- tive pulses instead of a single pulse. At the same time, the GREEN H2/A wire will supply two positive pulses instead of a single pulse. This makes it poss ...

  • Directed Electronics K10 - page 12

    13 Channels #4-6: Channels 4 through 6 are used to assign the arm, disarm and panic functions to sep- arate buttons on the remote control. T eaching a button to Channel 4 erases all information about that remote from memor y . Any auxiliar y functions that are desired will have to be reprogrammed. Similarly , if the remote is set up to use the sepa ...

  • Directed Electronics K10 - page 13

    14 remote configurations The transmitters can be programmed with the standard or single button arm/disarm configurations by using the Auto Learn functions in the Remote Coding. standard configuration A remote that uses the standard configuration operates similarly to many factor y keyless entry remotes. A standard configuration remote allows arming ...

  • Directed Electronics K10 - page 14

    15 power-up Power-up ensures that the when the system is powered up it will return to the same state it was in when power is disconnected. For a full description of power-up refer to the owner's manual. ...

  • Directed Electronics K10 - page 15

    16 3-Pin 2-Wire Door Lock Harness Override Switch Pro Secur ity Programmer ® ™ wiring quick reference guide ...

  • Directed Electronics K10 - page 16

    Get Started Get Protected Ungo Pro Security 661 W . Redondo Beach Blvd. Gardena, Ca. 90247 800-GO-CLARION © 2003 Directed Electroni cs, Inc . - All rights r eserved GK10 11-03 ...

メーカー Directed Electronics カテゴリー Network Card

Directed Electronics K10のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- K10の取扱説明書
- Directed Electronicsの製品カード
- パンフレット
- またはDirected Electronics K10の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Directed Electronics K10の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Directed Electronics K10の取り付け説明書、サービスマニュアル、簡易説明書、またはDirected Electronics K10のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Directed Electronics K10の製品を使用するにあたって最も人気のある説明書を閲覧できます。

Directed Electronics K10デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDirected Electronics K10を使用するのを助ける技術的文書のことです。説明書は通常、全てのDirected Electronics K10ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Directed Electronicsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Directed Electronics K10の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDirected Electronics K10の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Directed Electronics K10に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Directed Electronics K10デバイスの基本機能を使うにあたってのヒント。 Directed Electronics K10のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Directed Electronics K10に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDirected Electronics K10のメーカー/サービスへの連絡先に関する情報。

Directed Electronics K10についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDirected Electronics K10の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDirected Electronics K10で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)