Manuale per l’uso AB Soft MS6 SERIES

14 pagine 0.07 mb
Scarica

Vai alla pagina of 14

Summary
  • AB Soft MS6 SERIES - page 1

    Opal Pro to Mod TCP Page 1 Opal Pro MS6 SER IES AB Ethernet I P Interface Users Manual Revision 1.00 ...

  • AB Soft MS6 SERIES - page 2

    Opal Pro to Mod TCP Page 2 ...

  • AB Soft MS6 SERIES - page 3

    Opal Pro to Mod TCP Page 3 FOR YOUR SAFETY Only qualified personnel shoul d install this equipment, after first reading and understanding all the information in this manual. All instructions should be strictly adhered to. The user should consult Brock Solutions or a SAF OPAL Starters supplier for clarification of the contents of t his manual should ...

  • AB Soft MS6 SERIES - page 4

    Opal Pro to Mod TCP Page 4 ...

  • AB Soft MS6 SERIES - page 5

    Opal Pro to Mod TCP Page 5 Table of Conten ts INTRODUCTION .............................................................................................. 6 HARDWARE .................................................................................................... 6 JUMPER SET TINGS ................................................................. ...

  • AB Soft MS6 SERIES - page 6

    Opal Pro to Mod TCP Page 6 Opal Pro to Mod TC P Introduction The Opal Pro can be m onitored and controlled over an Ethernet communication network using the AB Ethernet IP pr otocol. The Opal Pro connects to the Ether net network through and optional Ethernet card that is mounted on the m ain Opal Pro control car d (CA530). Access is g ained to the ...

  • AB Soft MS6 SERIES - page 7

    Opal Pro to Mod TCP Page 7 LED Indicators Two bi-colour (red/green) LED indicators are mount ed beside the network connector. The upper LED indicates the Ethernet interface card stat us. LED State Ethernet Interface Card Status OFF No power Flashing Red Recoverable configuration fault ( card is not configured, contact Br ock Solutions for support) ...

  • AB Soft MS6 SERIES - page 8

    Opal Pro to Mod TCP Page 8 Op al Pro Paramete r Settings The parameters in t he Opal Pro used to con figure the Ehernet inter face card (group 14) ar e only accessible if a Ethernet interface card is inst alled. The parameter sett ings are as follows: Opal Pro Parameter Setting Description 2.02 Comm Module Ethernet Type of interface car d installed ...

  • AB Soft MS6 SERIES - page 9

    Opal Pro to Mod TCP Page 9 15.04 Comm Fault Enable Disable Enable – Opal Pro trips out on a communication fault Disable – Nothing happens on a communication fault 15.05 Comm Fault Time 0.1 to 5.0 secs This is the time sett ing that the Opal Pro uses to detect a communication fault. Bit 15 of the command word must change state twice with in the ...

  • AB Soft MS6 SERIES - page 10

    Opal Pro to Mod TCP Page 10 I/O Configuration The Opal Pro supports 4 input words and 51 output words. Their description is as follows: Input Words (Polled) AB Ethernet IP Name Description Bit 0 – Run Command Bit 1 – Jog Command Bit 2 – Reverse Comm and Bit 3 – Reset Command Bit 4 – DCI/Soft Stop Enable Bit 5 – Reserved Bit 6 – Reserv ...

  • AB Soft MS6 SERIES - page 11

    Opal Pro to Mod TCP Page 11 Output Words (Polled) AB Ethernet IP Name Description Bit 0 – Ready to Run (dr ive is enable and has 3 phase power) Bit 1 –Running (start is regulating) Bit 2 – Full On (star ter is phased fully on) Bit 3 – Up to Speed (st arted is phased fully on and the curr ent is below 105% of nameplate cur rent as set in 13. ...

  • AB Soft MS6 SERIES - page 12

    Opal Pro to Mod TCP Page 12 Relay Status Status of the Relay O utputs Bit 0 – Running Bit 1 – By-Pass Bit 2 – Shorted SCR Bit 3 – Reverse 1.07 Input Word 9 Bit 4 – Faulted 1.08 Input Word 10 Analog Output Analog Output value in Volts X 100 2.01 Input Word 11 Stack Size Opal Pro Stack Size in Amps 2.02 Input Word 12 Comm Module Type 0 – ...

  • AB Soft MS6 SERIES - page 13

    Opal Pro to Mod TCP Page 13 12.01 Input Word 27 Analog Output 16 = Current Refer ence 17 = Current Feedback 18 = Overload level 19 = Phase Angle 13.01 Input Word 28 Motor Amps Motor nameplate cur rent in Amps 13.02 Input Word 29 Motor Volts Motor nameplat e volts in Volts 13.03 Input Word 30 Service Factor Motor nameplate ser vice factor x 100 14.0 ...

  • AB Soft MS6 SERIES - page 14

    Opal Pro to Mod TCP Page 14 NOTE: The Opal Pro must have firmw are version 1.70 or higher. ...

Fabbricante AB Soft Categoria Network Card

I documenti che otteniamo dal fabbricante del dispositivoAB Soft MS6 SERIES possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici AB Soft
- manuali per l’uso MS6 SERIES
- schede prodotto AB Soft
- opuscoli
- o etichette energetiche AB Soft MS6 SERIES
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso AB Soft MS6 SERIES.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione AB Soft MS6 SERIES, manuali di manutenzione, brevi manuali o manuali utente AB Soft MS6 SERIES. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto AB Soft MS6 SERIES.

Manuali per l’uso simili

Manuale completo del dispositivo AB Soft MS6 SERIES, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare AB Soft MS6 SERIES dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti AB Soft MS6 SERIES.

Il manuale per l’uso completo AB Soft, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale AB Soft MS6 SERIES - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice AB Soft MS6 SERIES, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per AB Soft MS6 SERIES che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo AB Soft MS6 SERIES - che ci dovrebbe aiutare nei primi passi durante l'uso AB Soft MS6 SERIES
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del AB Soft MS6 SERIES
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio AB Soft MS6 SERIES in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su AB Soft MS6 SERIES?

Utilizza il modulo sottostante

Se non hai risolto il problema con AB Soft MS6 SERIES con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con AB Soft MS6 SERIES è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)