Bedienungsanleitung AB Soft MS6 SERIES

14 Seiten 0.07 mb
Download

Zur Seite of 14

Summary
  • AB Soft MS6 SERIES - page 1

    Opal Pro to Mod TCP Page 1 Opal Pro MS6 SER IES AB Ethernet I P Interface Users Manual Revision 1.00 ...

  • AB Soft MS6 SERIES - page 2

    Opal Pro to Mod TCP Page 2 ...

  • AB Soft MS6 SERIES - page 3

    Opal Pro to Mod TCP Page 3 FOR YOUR SAFETY Only qualified personnel shoul d install this equipment, after first reading and understanding all the information in this manual. All instructions should be strictly adhered to. The user should consult Brock Solutions or a SAF OPAL Starters supplier for clarification of the contents of t his manual should ...

  • AB Soft MS6 SERIES - page 4

    Opal Pro to Mod TCP Page 4 ...

  • AB Soft MS6 SERIES - page 5

    Opal Pro to Mod TCP Page 5 Table of Conten ts INTRODUCTION .............................................................................................. 6 HARDWARE .................................................................................................... 6 JUMPER SET TINGS ................................................................. ...

  • AB Soft MS6 SERIES - page 6

    Opal Pro to Mod TCP Page 6 Opal Pro to Mod TC P Introduction The Opal Pro can be m onitored and controlled over an Ethernet communication network using the AB Ethernet IP pr otocol. The Opal Pro connects to the Ether net network through and optional Ethernet card that is mounted on the m ain Opal Pro control car d (CA530). Access is g ained to the ...

  • AB Soft MS6 SERIES - page 7

    Opal Pro to Mod TCP Page 7 LED Indicators Two bi-colour (red/green) LED indicators are mount ed beside the network connector. The upper LED indicates the Ethernet interface card stat us. LED State Ethernet Interface Card Status OFF No power Flashing Red Recoverable configuration fault ( card is not configured, contact Br ock Solutions for support) ...

  • AB Soft MS6 SERIES - page 8

    Opal Pro to Mod TCP Page 8 Op al Pro Paramete r Settings The parameters in t he Opal Pro used to con figure the Ehernet inter face card (group 14) ar e only accessible if a Ethernet interface card is inst alled. The parameter sett ings are as follows: Opal Pro Parameter Setting Description 2.02 Comm Module Ethernet Type of interface car d installed ...

  • AB Soft MS6 SERIES - page 9

    Opal Pro to Mod TCP Page 9 15.04 Comm Fault Enable Disable Enable – Opal Pro trips out on a communication fault Disable – Nothing happens on a communication fault 15.05 Comm Fault Time 0.1 to 5.0 secs This is the time sett ing that the Opal Pro uses to detect a communication fault. Bit 15 of the command word must change state twice with in the ...

  • AB Soft MS6 SERIES - page 10

    Opal Pro to Mod TCP Page 10 I/O Configuration The Opal Pro supports 4 input words and 51 output words. Their description is as follows: Input Words (Polled) AB Ethernet IP Name Description Bit 0 – Run Command Bit 1 – Jog Command Bit 2 – Reverse Comm and Bit 3 – Reset Command Bit 4 – DCI/Soft Stop Enable Bit 5 – Reserved Bit 6 – Reserv ...

  • AB Soft MS6 SERIES - page 11

    Opal Pro to Mod TCP Page 11 Output Words (Polled) AB Ethernet IP Name Description Bit 0 – Ready to Run (dr ive is enable and has 3 phase power) Bit 1 –Running (start is regulating) Bit 2 – Full On (star ter is phased fully on) Bit 3 – Up to Speed (st arted is phased fully on and the curr ent is below 105% of nameplate cur rent as set in 13. ...

  • AB Soft MS6 SERIES - page 12

    Opal Pro to Mod TCP Page 12 Relay Status Status of the Relay O utputs Bit 0 – Running Bit 1 – By-Pass Bit 2 – Shorted SCR Bit 3 – Reverse 1.07 Input Word 9 Bit 4 – Faulted 1.08 Input Word 10 Analog Output Analog Output value in Volts X 100 2.01 Input Word 11 Stack Size Opal Pro Stack Size in Amps 2.02 Input Word 12 Comm Module Type 0 – ...

  • AB Soft MS6 SERIES - page 13

    Opal Pro to Mod TCP Page 13 12.01 Input Word 27 Analog Output 16 = Current Refer ence 17 = Current Feedback 18 = Overload level 19 = Phase Angle 13.01 Input Word 28 Motor Amps Motor nameplate cur rent in Amps 13.02 Input Word 29 Motor Volts Motor nameplat e volts in Volts 13.03 Input Word 30 Service Factor Motor nameplate ser vice factor x 100 14.0 ...

  • AB Soft MS6 SERIES - page 14

    Opal Pro to Mod TCP Page 14 NOTE: The Opal Pro must have firmw are version 1.70 or higher. ...

Produzent AB Soft Kategorie Network Card

Dokumente, die wir vom Produzenten des Geräts AB Soft MS6 SERIES erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen AB Soft
- Bedienungsanleitungen MS6 SERIES
- Produktkarten AB Soft
- Informationsbroschüren
- oder Energieetiketten AB Soft MS6 SERIES
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung AB Soft MS6 SERIES.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen AB Soft MS6 SERIES, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen AB Soft MS6 SERIES. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts AB Soft MS6 SERIES ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts AB Soft MS6 SERIES, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von AB Soft MS6 SERIES hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von AB Soft MS6 SERIES verständlich ist.

Eine gänzliche Bedienungsanleitung von AB Soft sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von AB Soft MS6 SERIES bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von AB Soft MS6 SERIES befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich AB Soft MS6 SERIES, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts AB Soft MS6 SERIES - die uns die ersten Schritte während der Nutzung von AB Soft MS6 SERIES erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit AB Soft MS6 SERIES hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von AB Soft MS6 SERIES im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich AB Soft MS6 SERIES?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit AB Soft MS6 SERIES nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit AB Soft MS6 SERIES hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)