Anaheim BLD72-1の取扱説明書

12ページ 1.03 mb
ダウンロード

ページに移動 of 12

Summary
  • Anaheim BLD72-1 - page 1

    1 BLD72, BLD72-1 Bilevel Step Motor Driver User’s Guide #L010011 910 East Orangefair Lane, Anaheim, CA 92801 e-mail: info@anaheimautomation.com (714) 992-6990 fax: (714) 992-0471 website: www.anaheimautomation.com ANAHEIM AUTOMATION ...

  • Anaheim BLD72-1 - page 2

    2 General Description The BLD72 is a step motor driver that can drive motors rated from 1 to 7 amps/phase (unipolar rating). It can handle 6 lead and 8 lead motors. This driver features a unipolar bilevel (or dual voltage) drive tech- nique with short and open circuit protection (with a Fault LED). A transformer is required to power up the driver. ...

  • Anaheim BLD72-1 - page 3

    3 Clock Modes The BLD72 has two clock options: Clock and Direction, or Dual Clock operation. Jumper JP2 is used to select the clock option. Basically JP2 selects Terminal 5 as either the Direction input or the CCW input. With the Clock and Direction option (most common option), clock pulses applied to the Clock input (Ter- minal 6) cause the motor ...

  • Anaheim BLD72-1 - page 4

    4 Fault Protection There are 3 types of fault detection. When a fault is detected, the driver turns off the motor current and the red Fault LED indicates which type of fault occurred. See the Troubleshooting section for more information. If the driver goes into a fault condition, the fault may be reset by turning the power OFF for at least 15 secon ...

  • Anaheim BLD72-1 - page 5

    5 Wiring Diagram The wiring diagram in Figure 5 shows the BLD72 with the AA2791 Transformer. For wiring with the AA2793 Transformer, refer to Figure 9. Motor Connections Figure 5 is a hookup diagram for typical BLD72 driver applications. Wiring connected to inputs must be separated from motor connections and all other possible sources of interferen ...

  • Anaheim BLD72-1 - page 6

    6 3. 750 MA X 4. 500 3. 100 2. 500 1. 450 MA X 1. 500 .8 00 M A X 2. 350 3. 570 3. 000 Transformer Drawings Note: The AA2793 transformer is the same physical size as the AA2791, but it has two sets of second- ary windings (to power two drivers) and a dual primary winding for 115/230V operation. Figure 6: Transformer Dimensions Figure 8: AA2793 Tran ...

  • Anaheim BLD72-1 - page 7

    7 Figure 9: Wiring for different line voltages for the AA2793 transformer. ...

  • Anaheim BLD72-1 - page 8

    8 Note: The BLD72 and BLD72-1 are the same except for the base plate. The BLD72 is a replacement driver for use in Driver Packs. The BLD72-1 is a modular driver which has a larger base plate. Dimensions Drawings Figure 11: BLD72-1 Dimensions Figure 10: BLD72 Dimensions ...

  • Anaheim BLD72-1 - page 9

    9 13 Pin Terminal Description Motor Compatibility Add suffix “ S ” for single-ended shaft, or suffix “ D ” for double-ended shaft. Notes: Other motors not listed above may be compatible with this driver. Anaheim Automation carries a full-line of standard and high torque step motors. Contact the factory regarding compatibility. See back cove ...

  • Anaheim BLD72-1 - page 10

    10 Specifications Control Inputs (All) : (Terminals 5, 6, 8, 9) TTL-compatible Logic “ 0 ” - 0 to 0.8 V Logic “ 1 ” - 3.5 to 5.0 V Fault Reset: (Terminal 4) Pulled up to +5VDC through a 10k Ohm resistor Logic “ 1 ” (open) - Driver enabled and Fault detection enabled Logic “ 0 ” - Resets a Fault condition (driver is disabled when thi ...

  • Anaheim BLD72-1 - page 11

    11 Troubleshooting If a Fault occurs, reset the Fault by applying a logic “ 0 ” to the Reset Fault Input (terminal 4) for at least 100ms (or by cycling power OFF for at least 15 seconds). After resetting, try to run the motor again. If the driver faults again then check the conditions listed below. Is the LED blinking slowly? (Once a second) Th ...

  • Anaheim BLD72-1 - page 12

    12 Torque Speed Curves ANAHEIM AUTOMATION ...

メーカー Anaheim カテゴリー Power Supply

Anaheim BLD72-1のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- BLD72-1の取扱説明書
- Anaheimの製品カード
- パンフレット
- またはAnaheim BLD72-1の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Anaheim BLD72-1の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Anaheim BLD72-1の取り付け説明書、サービスマニュアル、簡易説明書、またはAnaheim BLD72-1のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Anaheim BLD72-1の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Anaheim BLD72-1デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAnaheim BLD72-1を使用するのを助ける技術的文書のことです。説明書は通常、全てのAnaheim BLD72-1ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Anaheimの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Anaheim BLD72-1の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAnaheim BLD72-1の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Anaheim BLD72-1に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Anaheim BLD72-1デバイスの基本機能を使うにあたってのヒント。 Anaheim BLD72-1のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Anaheim BLD72-1に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAnaheim BLD72-1のメーカー/サービスへの連絡先に関する情報。

Anaheim BLD72-1についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAnaheim BLD72-1の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAnaheim BLD72-1で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)