Hobart D340の取扱説明書

12ページ 1.29 mb
ダウンロード

ページに移動 of 12

Summary
  • Hobart D340 - page 1

    FORM 19104 Rev. A (8-98) D340 MIXER D340 MIXERS D340 W/BRAKE ML - 104484 D340 W/O BRAKE ML - 104483 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 ...

  • Hobart D340 - page 2

    – 2 – © HOBART CORPORATION, 1994 MODEL D340 MIXER ...

  • Hobart D340 - page 3

    – 3 – Installation, Operation, and Care of MODEL D340 MIXERS SA VE THESE INSTRUCTIONS GENERAL The D340 Mixer is a medium duty mixer which develops 1 1 / 2 horsepower and features a timer, thermal overload protection, and a #12 attachment hub as standard equipment. A variety of agitators are available for use on either the standard 40 quart bowl ...

  • Hobart D340 - page 4

    – 4 – WARNING : ELECTRICAL AND GROUNDING CONNECTION MUST COMPLY WITH THE APPLICABLE PORTION OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT. A hole for 3 ⁄ 4 " trade size conduit is loc ...

  • Hobart D340 - page 5

    – 5 – Start Button Stop Button Timer Gear Shift Lever PL-40142-1 OPERA TION WARNING : MOVING BEATER IN BOWL, KEEP HANDS, CLOTHING, AND UTENSILS OUT WHILE IN OPERATION, DO NOT USE WITHOUT INTERLOCKED GUARD. Every D340 mixer is equipped with either an Electro-Mechanical Timer Control (described at the bottom of this page) or a Programmable Timer ...

  • Hobart D340 - page 6

    – 6 – PROGRAMMABLE TIMER CONTROLLER (when equipped) At Idle, the timer display [ – – : – – ] shows that no time has been set (Fig. 4). Fig. 4 Timer Keys Programming Function (if the mixer is not mixing). P1 Contains up to four preset times. Displays each preset time sequentially. P2 Contains up to four additional preset times. Displays ...

  • Hobart D340 - page 7

    – 7 – PROGRAMMABLE TIMER CONTROLLER (when equipped) continued Using the Preset Keys, P1 or P2, to set the Mixing Time . . . Each preset key has four time settings. The indicator above the number 1, 2, 3, or 4 and the P1 or P2 indicator light identify which preset time is being displayed. The chart below shows the default settings; the next page ...

  • Hobart D340 - page 8

    – 8 – PROGRAMMABLE TIMER CONTROLLER (when equipped) continued To Revise the Preset Mixing Times contained in P1 or P2 . . . Each preset key has four preset time settings. The indicator above the number 1, 2, 3, or 4 and the P1 or P2 indicator light identify which preset time is being displayed. Beginning from the Idle display [ – – : – ? ...

  • Hobart D340 - page 9

    – 9 – CHANGING SPEEDS The GEAR SHIFT LEVER is used to change speeds. Always stop the mixer before changing speeds. To change speeds, push the STOP button, move the gear shift lever to the desired speed, and restart the mixer by pushing the START button. NOTE : If you do not stop the mixer to change speeds, it will automatically shut itself off ...

  • Hobart D340 - page 10

    – 10 – Bowl Guard (Fig. 5) The Wire Cage Assembly on the Bowl Guard can be rotated out-of-the-way to add ingredients or access the bowl and agitator. To rotate the Wire Cage Assembly to the rear . . . Push the Latch in to release the Centering Pin from the Centering Ramp. Note how the grooves on the nylon Retainers allow the Wire Cage to ride a ...

  • Hobart D340 - page 11

    – 11 – Attachments To install an attachment, loosen the attachment hub thumb screw and remove the plug. Insert the attachment into the attachment hub, making certain that the square shank of the attachment is in the square driver of the mixer. Secure the attachment by tightening the thumb screw. Move the gear shift lever to the desired speed. W ...

  • Hobart D340 - page 12

    – 12 – PL-40172-1 Bowl Lift Slideways Bowl Lift Slideways The slideways (Fig. 6) should be lubricated once each month. Remove the apron (secured by four thumb screws) from the front of the pedestal. Lightly coat both slideways with Lubriplate 630AA (supplied). Replace the apron and thumbscrews. Fig. 6 TROUBLESHOOTING SYMPTOMS POSSIBLE CAUSES Mi ...

メーカー Hobart カテゴリー Mixer

Hobart D340のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- D340の取扱説明書
- Hobartの製品カード
- パンフレット
- またはHobart D340の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Hobart D340の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Hobart D340の取り付け説明書、サービスマニュアル、簡易説明書、またはHobart D340のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Hobart D340の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Hobart D340デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHobart D340を使用するのを助ける技術的文書のことです。説明書は通常、全てのHobart D340ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Hobartの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Hobart D340の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHobart D340の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Hobart D340に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Hobart D340デバイスの基本機能を使うにあたってのヒント。 Hobart D340のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Hobart D340に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHobart D340のメーカー/サービスへの連絡先に関する情報。

Hobart D340についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHobart D340の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHobart D340で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)