JAI CV-A50の取扱説明書

27ページ 1.57 mb
ダウンロード

ページに移動 of 27

Summary
  • JAI CV-A50 - page 1

    Industrial Monochrome CCD Camera CV -A50 / CV -A60 Operation Manual Camera: CV -A50 Revision B CV -A60 Revision A Manual: Version 2.1 A50Manualjul14.doc JPT 14-07-03 ...

  • JAI CV-A50 - page 2

    CV-A50 / CV-A60 DECLARA TION OF CONFORMITY AS DEFINED BY THE COUNCIL DIRECTIVE 89/336/EE C EMC (ELECTROMAGNETIC COMPAB ILITY) WE HEREWITH DECLARE THAT THIS PRODUCT COMPLIES WITH THE FOLOWING PROV ISIONS APPLYING TO IT. EN-50081-1 EN-50082-1 Table of Contents 1. General................................................................................. ...

  • JAI CV-A50 - page 3

    CV-A50 / CV-A60 1. Gener al The difference from the previous manual is that the CCD sen sor in CV-A50 is changed to new types. Now the used CCD sensors are: ICX-408AL-6, 409AL -6, 418ALL-6, 419ALL-6. The CV-A50/A60 is a range of monochrome CCIR and EIA interlaced 1/2” and 1 /3” CCD cameras, designed for automated application, featuring an extre ...

  • JAI CV-A50 - page 4

    CV-A50 / CV-A60 4. Camer a Housing and Dimensions Fig. 1. Locations and dimensions. 1. 12 pin Hirose connector for frame grabber interfacing and power (12V DC). 2. BNC connector for video output. VS 1.0 Vpp 75 Ohm. 3. 6 pin Hirose connector for trigger input and RS-232C control interface. 4. Gain potentiometer for manual gain setting. 5. Mounting h ...

  • JAI CV-A50 - page 5

    CV-A50 / CV-A60 5. Pin Assignment 5.1. 12-pin Multi-connector (DC- IN/VIDEO OUT, EXT.HD/VD IN) Type: HR10A-10R-12PB-01 (Hirose) male Seen from rear. Pin configuration is compatible with EIAJ standard Pin no. Signal Remarks 1 GND 2 +12 V DC input 3 GND 4 Video output Parallel with t he BNC connector. 5 GND 6 HD input /HD output *) SW2.1 on for 75 ? ...

  • JAI CV-A50 - page 6

    CV-A50 / CV-A60 5.3. Input and Output Circuits In the following schematic diagrams the input and outpu t circuits for video and timing signa ls are shown. Jumper settings are shown as for fact ory default. For alternative connections refer to “10.1. CV-A50/60 emulating CV-M50 interfacing.” 5.3.1. Video output GND #4/ 12 75 Video Out put NC 82p ...

  • JAI CV-A50 - page 7

    CV-A50 / CV-A60 6. F unctions and Operations Apart from the standard continuous operatio n, the CV-A50/60 features three external asynchronous trigger modes (edge pr e-select, pulse width controlled and start/stop) and a special frame-delay readout mode. Long integration time m ode is also supported. 6.1. Basic functions Some of the primary camera ...

  • JAI CV-A50 - page 8

    CV-A50 / CV-A60 6.2. Input-output of HD/VD Signals In the default setting the camera will accept external HD/VD signals on pin 6 and 7 of the 12 pin Hirose connector. If external HD/VD is applied, th e camera will synchronize to it. If no external sync signals are applied, the camera will oper ate with its internal x-tal controlled sync. The time r ...

  • JAI CV-A50 - page 9

    CV-A50 / CV-A60 Fig. 10. Horizontal timing details and pixel numbering for the CCD array. CCIR Fig. 11. Horizontal timing details and pixel numbering for the CCD array. EIA - 8 - ...

  • JAI CV-A50 - page 10

    CV-A50 / CV-A60 Fig. 12. Vertical timing details for interlaced. CCIR Fig. 12A. Vertical timing details for non-interlaced. CCIR - 9 - ...

  • JAI CV-A50 - page 11

    CV-A50 / CV-A60 Fig. 13. Vertical timing details for interlaced. EIA Fig. 13A. Vertical timing details for non-interlaced. EIA - 10 - ...

  • JAI CV-A50 - page 12

    CV-A50 / CV-A60 6.4. External Trigger Modes This camera has 5 external asynchr onous trigger modes, which can be s et by RS-232C commands. 1. Edge Pre-select Mode.TR=1 Pre-selected exposure. (SM=0, SM=1) 2. Pulse Width Control Mode. TR=2 Pulse width controlled exposure. 3. Frame Delay read out mode. TR=3 PWC exposure read out by ext. VD. 4. Long Ti ...

  • JAI CV-A50 - page 13

    CV-A50 / CV-A60 6.5. Edge Pre-select Mode The leading edge of the trigger pulse initiates the exposure. The exposure time (accumulation time) is governed by the pre-defined shutter sp eed set by RS-232C. The resulting video is output as “odd field” for EIA and “even field” f or CCIR, and appear 9H (EIA9 or 10H (CCIR) after the leadin g edge ...

  • JAI CV-A50 - page 14

    CV-A50 / CV-A60 6.6. Pulse Width Control Mode The leading edge of the trigger pulse initiates the exposure. The exposure time (accumulation time) is governed by duration of the trigger pulse. The resulting video is output as “odd field” for EIA and “even field” f or CCIR, and appear 9H (EIA9 or 10H (CCIR) after the leadin g edge of WEN (pol ...

  • JAI CV-A50 - page 15

    CV-A50 / CV-A60 6.7. Frame-delay read out Mode This mode allows simultaneous c apture of multiple camera using a common external trigger pulse subsequent multiplexed (sequential) readou t using a single input frame grab ber, as the user has control over when the image is read ou t from the CCD sensor. The exposure starts at the falling edge of the ...

  • JAI CV-A50 - page 16

    CV-A50 / CV-A60 6.8. Long Time Exposure Mode The exposure time is the interval between 2 ext. VD pulses sent to the VD input of the camera (Pin No. 7 of the 12-pin Hirose connector). The ex posure starts after input of the first ext. VD pulse, and ends after the next input of the ne xt ext. VD pulse, which ag ain starts a new exposure. The long tim ...

  • JAI CV-A50 - page 17

    CV-A50 / CV-A60 6.9. Start/Stop Mode The exposure time is controlled by the interval between the ext. trigger and the ext. VD signal. The exposure starts at the first HD pulse after t he falling edge of the ext. trigger, and stops 14.5 H after the falling edge of the VD pulse. It means that the trigger pulse must be applied after the external VD pu ...

  • JAI CV-A50 - page 18

    CV-A50 / CV-A60 Important notes on using this mode: - • As the start of exposure will be sync hronized with the internal H signal, the start of exposure may be shifted by max 1H. • To avoid this shift (jitter), synchro nize the camera with an external HD and m ake sure that the trigger pulse aligns to the HD signal as shown in Fig. 14. • For ...

  • JAI CV-A50 - page 19

    CV-A50 / CV-A60 7. Configuring the Camer a 7.1. RS-232C control. All configuration of the A50/60 camera is done vi a the RS -232C port. The camera can be set up from a PC running terminal emulator softwa re, or using JAI´s camera control software. Below is the description of the ASCII based short command p rotocol. Communication setting. Baud Rate ...

  • JAI CV-A50 - page 20

    CV-A50 / CV-A60 7.2. CV-A50/60 RS-232C command list. Command Name Format Parameter Remarks A – General settings and useful commands EB Echo Back EB= [ Param. ] <CR><LF> 0=Echo off 1=Echo on Off at power up ST Camera Status request ST?<CR><LF> Actual setting HP Online Help reques t HP?<CR><LF> Command list VN Fi ...

  • JAI CV-A50 - page 21

    CV-A50 / CV-A60 7.3. Camera Control Tool for CV-A50/60 From www.jai.com CV-A50/60 Camera Control Tool for Wind ows 98/NT/2000 can be downloaded. The control tool contents a camera control program and tools for m aking your own program. Below the different windows are sh own. Control bar Windows for all functions Fig. 28. Windows from Camera Tools. ...

  • JAI CV-A50 - page 22

    CV-A50 / CV-A60 7.4. Internal Switch and Jumper Settings. 7.4.1 HD/VD input-output selection In the default setting the camera will accept external HD/VD signals on pins 6 and 7 of the 12 pin Hirose connector. The compos ite video signal from the camera will be synchr onized to an external HD/VD source connected to the camera. TTL level (between 2 ...

  • JAI CV-A50 - page 23

    CV-A50 / CV-A60 8. Specifications Specifications CV-A50C CV-A60C CV-A50E CV-A60E Scanning system CCIR, 25 frames/sec. 625 lines, 2:1 Interlaced EIA. 30 frames/sec. 525 lines, 2:1 Interlaced Frame rate (Full frame) 50 Hz 59.94 Hz Line frequency 15.625 kHz 15.734 kHz Pixel frequency 14.1875 MHz 14.3182 MHz CCD sensor 1/2”. CV-A50 *) CCD sensor 1/3? ...

  • JAI CV-A50 - page 24

    CV-A50 / CV-A60 9. Spectr al Sensiti v ity 400 500 600 700 800 900 Wave Length (nm) 1.0 0.8 0.6 0.4 0.2 0.0 Relative Response 1000 Fig. 30. Spectral sensitivity. 10. Appendix 10.1. CV-A50 or CV-A60 emul ating CV-M50 interfacing The CV-A50 and CV-A60 have a sligh tly different pin configuration on th e 12-pin Hirose connector, compared to the M-seri ...

  • JAI CV-A50 - page 25

    CV-A50 / CV-A60 10.2. WEN out on pin 6 on 6 pin connector Instead of EEN output on pin #6 on the 6 pin Hirose connector, WEN c an be output by jumper settings. The 2 jumpers are found on the main bo ard PK8275B, if the bottom plate is removed. JP1 JP2 Signal on pin #6 JP1 JP2 Remark EEN out open short default WEN out short open Configuration shown ...

  • JAI CV-A50 - page 26

    CV-A50 / CV-A60 10.4. Precautions Personnel not trained in dealing with similar elec tronic devices should not service this camera. The camera contains components sensitive to el ectrostatic discharge. The handling of these devices should follow the requirements of electrostatic se nsitive components. Do not attempt to disassemble this camera. Do n ...

  • JAI CV-A50 - page 27

    CV-A50 / CV-A60 11. Users Record Camera type: CV-A50/60 CCIR/EIA Revision: CV-A60 Revision A. CV-A50 revision B Serial No. …………….. For camera revision hi story, please contact your local JAI d istributor. Users Mode Settings: Users Modifications: Company and product names mentioned in this manual are trademarks or registered trademarks of ...

メーカー JAI カテゴリー Security Camera

JAI CV-A50のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CV-A50の取扱説明書
- JAIの製品カード
- パンフレット
- またはJAI CV-A50の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、JAI CV-A50の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、JAI CV-A50の取り付け説明書、サービスマニュアル、簡易説明書、またはJAI CV-A50のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、JAI CV-A50の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

JAI CV-A50デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがJAI CV-A50を使用するのを助ける技術的文書のことです。説明書は通常、全てのJAI CV-A50ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

JAIの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. JAI CV-A50の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははJAI CV-A50の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。JAI CV-A50に関してこのドキュメントで見つけることができる全てのヒントの目次
3. JAI CV-A50デバイスの基本機能を使うにあたってのヒント。 JAI CV-A50のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。JAI CV-A50に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるJAI CV-A50のメーカー/サービスへの連絡先に関する情報。

JAI CV-A50についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもJAI CV-A50の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJAI CV-A50で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)