Hobart 5801の取扱説明書

12ページ 0.62 mb
ダウンロード

ページに移動 of 12

Summary
  • Hobart 5801 - page 1

    FORM 16322 Rev. A (11-95) MODEL 5801 MEA T SA W MODEL 5801 ML-38674 EXECUTIVE OFFICES 701 RIDGE AVENUE TROY, OHIO 45374-0001 N S T R U C T I O N S I ...

  • Hobart 5801 - page 2

    –2– Installation, Operation, and Care of MODEL 5801 MEA T SA W SA VE THESE INSTRUCTIONS GENERAL The 5801 Meat Saw is rugged, durable, and easy to clean. The saw is equipped with a water resistant 3 HP electric motor and direct gear drive transmission that provides a blade speed of 3500 feet per minute. The carriage (Fig.1) has stainless steel b ...

  • Hobart 5801 - page 3

    –3– PL-40847-1 GA UGE PLA TE HANDLE INST ALLA TION UNPACKING AND ASSEMBLY Immediately after unpacking the meat saw, check for possible shipping damage. If the meat saw is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, test the electrical service to make sure it agrees ...

  • Hobart 5801 - page 4

    –4– UPPER PULLEY COVER (Plastic - Standard) The plastic upper pulley cover (Fig. 5) should be installed on the two hinge-retainers at the top and securely latched at the bottom during use. To remove the plastic upper pulley cover for cleaning, release the latch at the bottom and remove from the hinge-retainers at the top. UPPER PULLEY COVER (St ...

  • Hobart 5801 - page 5

    –5– UPPER AND LOWER PULLEYS The upper and lower pulleys are assembled on the upper and lower pulley shafts; the latch on each pulley should be seated in the groove of the pulley shaft (Fig. 7). Pulleys can be removed after the blade has first been loosened and removed. Upper and lower pulleys are interchangeable. COLUMN GUARD The column guard ( ...

  • Hobart 5801 - page 6

    –6– PL-40838-1 LOWER GUIDE HOLDER LOWER BLADE GUIDE ASSEMBL Y CARRIAGE In use, the carriage can roll back and forth between the left carriage stop (Fig. 9) and the right carriage stop, assuming the spring loaded carriage lock (Fig. 5) has not locked the carriage in a stationary position. To remove the carriage, turn either of the carriage stops ...

  • Hobart 5801 - page 7

    –7– REMOVING THE BLADE Remove the upper and lower pulley covers. Raise the gauge plate to its vertical position. Remove the right table by lifting its right side and sliding the table to the right to free it from the locating pins. Remove the column guard. Turn the tension adjuster counterclockwise until it stops (this will release tension on t ...

  • Hobart 5801 - page 8

    –8– ELECTRICAL CONNECTIONS WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON. ELECTRICAL DATA Model Volts / Her ...

  • Hobart 5801 - page 9

    –9– OPERA TION SAFETY DEVICES INCORPORATED IN THIS SAW MUST BE IN THEIR CORRECT OPERATING POSITIONS ANYTIME THE SAW IS IN USE. SAFETY FEATURES Upper Guide and Guard Assembly Before turning the saw on, raise or lower the upper guide and guard assembly by grasping the hand knob and sliding up or down so the cutting zone is only as high as necessa ...

  • Hobart 5801 - page 10

    –1 0– GAUGE PLATE When making several cuts of the same thickness (or when using the pusher plate), set the gauge plate as desired (Fig. 13) by pushing the lock lever and sliding the gauge plate to the thickness you want. A reference scale on the table indicates the thickness of cut. If the gauge plate is not needed, you may release the lock lev ...

  • Hobart 5801 - page 11

    –1 1– CLEANING AND SANITIZING WARNING : DISCONNECT ELECTRICAL POWER AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON BEFORE CLEANING THIS MACHINE. The saw must be thoroughly cleaned and sanitized: Before first use; After each day's operation; Anytime it is not to be used for an extended period of time; or ...

  • Hobart 5801 - page 12

    –1 2– MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON. LUBRICATION The motor has permanently lubricated ball bearings and requires no additional lubrication. The slide bar for the upper guide and guard assembly also requires no lubrication. Occasionally, ...

メーカー Hobart カテゴリー Kitchen Utensil

Hobart 5801のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 5801の取扱説明書
- Hobartの製品カード
- パンフレット
- またはHobart 5801の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Hobart 5801の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Hobart 5801の取り付け説明書、サービスマニュアル、簡易説明書、またはHobart 5801のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Hobart 5801の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Hobart 5801デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHobart 5801を使用するのを助ける技術的文書のことです。説明書は通常、全てのHobart 5801ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Hobartの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Hobart 5801の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHobart 5801の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Hobart 5801に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Hobart 5801デバイスの基本機能を使うにあたってのヒント。 Hobart 5801のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Hobart 5801に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHobart 5801のメーカー/サービスへの連絡先に関する情報。

Hobart 5801についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHobart 5801の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHobart 5801で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)