English dropdown-ico

Manual Hobart 5801

12 pages 0.62 mb
Download

Go to site of 12

Summary
  • Hobart 5801 - page 1

    FORM 16322 Rev. A (11-95) MODEL 5801 MEA T SA W MODEL 5801 ML-38674 EXECUTIVE OFFICES 701 RIDGE AVENUE TROY, OHIO 45374-0001 N S T R U C T I O N S I ...

  • Hobart 5801 - page 2

    –2– Installation, Operation, and Care of MODEL 5801 MEA T SA W SA VE THESE INSTRUCTIONS GENERAL The 5801 Meat Saw is rugged, durable, and easy to clean. The saw is equipped with a water resistant 3 HP electric motor and direct gear drive transmission that provides a blade speed of 3500 feet per minute. The carriage (Fig.1) has stainless steel b ...

  • Hobart 5801 - page 3

    –3– PL-40847-1 GA UGE PLA TE HANDLE INST ALLA TION UNPACKING AND ASSEMBLY Immediately after unpacking the meat saw, check for possible shipping damage. If the meat saw is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, test the electrical service to make sure it agrees ...

  • Hobart 5801 - page 4

    –4– UPPER PULLEY COVER (Plastic - Standard) The plastic upper pulley cover (Fig. 5) should be installed on the two hinge-retainers at the top and securely latched at the bottom during use. To remove the plastic upper pulley cover for cleaning, release the latch at the bottom and remove from the hinge-retainers at the top. UPPER PULLEY COVER (St ...

  • Hobart 5801 - page 5

    –5– UPPER AND LOWER PULLEYS The upper and lower pulleys are assembled on the upper and lower pulley shafts; the latch on each pulley should be seated in the groove of the pulley shaft (Fig. 7). Pulleys can be removed after the blade has first been loosened and removed. Upper and lower pulleys are interchangeable. COLUMN GUARD The column guard ( ...

  • Hobart 5801 - page 6

    –6– PL-40838-1 LOWER GUIDE HOLDER LOWER BLADE GUIDE ASSEMBL Y CARRIAGE In use, the carriage can roll back and forth between the left carriage stop (Fig. 9) and the right carriage stop, assuming the spring loaded carriage lock (Fig. 5) has not locked the carriage in a stationary position. To remove the carriage, turn either of the carriage stops ...

  • Hobart 5801 - page 7

    –7– REMOVING THE BLADE Remove the upper and lower pulley covers. Raise the gauge plate to its vertical position. Remove the right table by lifting its right side and sliding the table to the right to free it from the locating pins. Remove the column guard. Turn the tension adjuster counterclockwise until it stops (this will release tension on t ...

  • Hobart 5801 - page 8

    –8– ELECTRICAL CONNECTIONS WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON. ELECTRICAL DATA Model Volts / Her ...

  • Hobart 5801 - page 9

    –9– OPERA TION SAFETY DEVICES INCORPORATED IN THIS SAW MUST BE IN THEIR CORRECT OPERATING POSITIONS ANYTIME THE SAW IS IN USE. SAFETY FEATURES Upper Guide and Guard Assembly Before turning the saw on, raise or lower the upper guide and guard assembly by grasping the hand knob and sliding up or down so the cutting zone is only as high as necessa ...

  • Hobart 5801 - page 10

    –1 0– GAUGE PLATE When making several cuts of the same thickness (or when using the pusher plate), set the gauge plate as desired (Fig. 13) by pushing the lock lever and sliding the gauge plate to the thickness you want. A reference scale on the table indicates the thickness of cut. If the gauge plate is not needed, you may release the lock lev ...

  • Hobart 5801 - page 11

    –1 1– CLEANING AND SANITIZING WARNING : DISCONNECT ELECTRICAL POWER AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON BEFORE CLEANING THIS MACHINE. The saw must be thoroughly cleaned and sanitized: Before first use; After each day's operation; Anytime it is not to be used for an extended period of time; or ...

  • Hobart 5801 - page 12

    –1 2– MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON. LUBRICATION The motor has permanently lubricated ball bearings and requires no additional lubrication. The slide bar for the upper guide and guard assembly also requires no lubrication. Occasionally, ...

Manufacturer Hobart Category Kitchen Utensil

Documents that we receive from a manufacturer of a Hobart 5801 can be divided into several groups. They are, among others:
- Hobart technical drawings
- 5801 manuals
- Hobart product data sheets
- information booklets
- or energy labels Hobart 5801
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hobart 5801.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hobart 5801, service manual, brief instructions and user manuals Hobart 5801. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hobart 5801.

Similar manuals

A complete manual for the device Hobart 5801, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hobart 5801 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hobart 5801.

A complete Hobart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hobart 5801 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hobart 5801, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hobart 5801, that we can find in the current document
3. Tips how to use the basic functions of the device Hobart 5801 - which should help us in our first steps of using Hobart 5801
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hobart 5801
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hobart 5801 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hobart 5801?

Use the form below

If you did not solve your problem by using a manual Hobart 5801, ask a question using the form below. If a user had a similar problem with Hobart 5801 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)