Wayne-Dalton 9800の取扱説明書

20ページ 5.35 mb
ダウンロード

ページに移動 of 20

Summary
  • Wayne-Dalton 9800 - page 1

    IMPORT ANT NO TICES! The complete Installation Instructions and Owner’ s Manual are available at no charge from: Wayne-Dalton, a Division Of Overhead Door Corporation, P .O. Box 67, Mt. Hope, OH., 44660, Or Online At www.W ayne-Dalton.com Wayne-Dalton highly recommends that you read and fully understand the Installation Instructions and Owner’ ...

  • Wayne-Dalton 9800 - page 2

    Important Safety Instructions DEFINITION OF KEY WORDS USED IN THIS MANUAL: W ARNING W ARNING INDICA TES A POTENTIALL Y HAZARDOUS SITUA TION WHICH; IF NOT AVOIDED , COULD RESUL T IN SEVERE OR FA T AL INJURY . CAUTION: PROPER TY DAMAGE OR INJURY CAN RESUL T FROM FAILURE TO FOLLOW INSTRUCTIONS. IMPORT ANT : REQUIRED STEP FOR SAFE AND PROPER DOOR OPERA ...

  • Wayne-Dalton 9800 - page 3

    3/8”- 16 Hex nuts (as required) 1/4”- 20 Flanged hex nuts (as required) (2) 5/16” Washers 5/16”-18 Hex nuts (as required) 1/4”-14 x 5/8” Self tapping screws (as required) 3/8”-16 x 3/4” Truss head bolts (as required) 1/4”-20 x 11/16” Self drilling screws (as required) (2) 5/16”-18 x 3/4” Carriage bolts (as required) 1/4”-2 ...

  • Wayne-Dalton 9800 - page 4

    side of the jamb, fit the weatherstrip up tight against the temporarily attached weatherstrip in the header and flush with the inside edge of the jamb. T emporarily secure the weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom section from falling out of the opening during installation. Equally space nails ap ...

  • Wayne-Dalton 9800 - page 5

    5 A. FLAG ANGLES (AS REQUIRED): A1. Quick Install (Q.I.) Flag Angles A2. Fully Adjustable (F .A.) Flag Angles B. JAMB BRACKETS (AS REQUIRED): B1. Quick Install (Q.I.) Jamb Brackets B2. Fully Adjustable (F .A.) Jamb Brackets C. TRACK ROLLERS (AS REQUIRED): C1. Short Stem T rack Rollers C2. Long Stem T rack Rollers D. GRADUA TED END HINGES: D1. Singl ...

  • Wayne-Dalton 9800 - page 6

    INST ALLA TION Before installing your door , be certain that you have read and followed all of the instruc- tions covered in the pre-installation section of this manual. Failure to do so may result in an improperly installed door . NOTE: Reference TDS 160 for general garage door terminology at www.dasma.com . Quick Install Flag Angles Tools Require ...

  • Wayne-Dalton 9800 - page 7

    pattern. Secure jamb bracket using (1) 1/4” - 20 x 9/16” track bolt and (1) 1/4” - 20 flange hex nut. Repeat for other side. T o attach the center jamb bracket, locate lower hole of the hole / slot pattern of the 2nd hole set on the vertical track. Secure jamb bracket using (1) 1/4” - 20 x 9/16” track bolt and (1) 1/4” - 20 flange hex ...

  • Wayne-Dalton 9800 - page 8

    Stacking Sections Tools Required: Power drill, 7/16” Socket driver 8 NOTE: The sections can be identified by the graduation of the factory installed end hinges. The smallest graduated end hinge on section should be stacked on top of the bottom section, with each graduated end hinge increasing as the sections are stacked, see Parts Breakdown. NOT ...

  • Wayne-Dalton 9800 - page 9

    T op section T op section Nail Door width + 3-3/8” to 3-1/2” 1-11/16” to 1-3/4” Flag angle Flag angle Vertical track against track rollers Horizontal Tracks Tools Required: Ratchet wrench, 9/16” Socket, 9/16” Wrench, level, Step ladder 12 NOTE: Depending on your door , you may have Quick Install Flag Angles, Fully Adjustable Flag Angles ...

  • Wayne-Dalton 9800 - page 10

    on top of the flag angles. NOTE: Cable drum assemblies are marked right and left hand. Cable drums and T orqueMas- ter ® spring tube assembly is cam shaped to fit together only one way . Starting on the right hand side, pre-wrap the cable drum with the counterbalance lift cable 1-1/2 wraps, as shown. Position the T orqueMaster ® spring tube ass ...

  • Wayne-Dalton 9800 - page 11

    seated in the first and second grooves of the cable drum. Pull on the end of the cable to remove all cable slack. Snug the set screw and then tighten an additional 1-1/2 turns. Measure approximately 6” of cable and cut off excess cable. Insert end of the cable into the hole of cable drum. Repeat for left hand cable drum assembly . IMPORT ANT : E ...

  • Wayne-Dalton 9800 - page 12

    perforated angle (may not be supplied), (2) 5/16” x 1-5/8” hex head lag screws and (3) 5/16” bolts with nuts (may not be supplied), fabricate rear back hangs for the horizontal tracks. Attach the horizontal tracks to the rear back hangs with 5/16” - 18 x 1” hex bolts and nuts (may not be supplied). Horizontal tracks must be level and para ...

  • Wayne-Dalton 9800 - page 13

    roller . This is to prevent the garage door from rising while adjusting the counterbalance spring(s). IMPORT ANT : TO ADJUST SPRINGS, ONL Y ADD OR REMOVE A MAXIMUM OF 3/10 OF A TURN (THREE TEETH ON THE RATCHET WHEEL) A T A TIME. BOTH SIDES NEED TO BE ADJUSTED EQUALL Y ON DOUBLE SPRING DOORS. Add spring tension: The ratchet wheel is made of 10 teeth ...

  • Wayne-Dalton 9800 - page 14

    TorqueMaster ® Plus Reset Instructions IMPORT ANT : THE DRA WBAR OPERA TOR FORCE SETTINGS MUST BE ADJUSTED AC- CORDING TO THE MANUF ACTURER’S INSTR UCTIONS. SOME LIGHTER WEIGHT DOORS ARE DESIGNED TO OPERA TE WITH A SINGLE COUNTERBALANCE SPRING. IF THA T COUNTER- BALANCE SPRING BREAKS AND THE DRAWBAR OPERA TOR’S FORCE SETTINGS ARE NOT ADJUSTED ...

  • Wayne-Dalton 9800 - page 15

    Pull Down Rope W ARNING W ARNING DO NOT INST ALL PULL DOWN ROPE ON DOORS WITH OPERA TORS. CHILDREN MA Y BECOME ENT ANGLED IN THE ROPE CAUSING SEVERE OR F A T AL INJURY . Measure and mark the jamb approximately 48” to 50” (1220 to 1270 mm) from floor on the right or left side of jamb. Drill 1/8” pilot hole for no. 6 screw eye. Tie the pull do ...

  • Wayne-Dalton 9800 - page 16

    Cleaning Y our Garage Door IMPORT ANT : DO NOT USE A PRESSURE WASHER ON YOUR GARAGE DOOR! While factory-applied finishes on garage doors are durable, it is desirable to clean them on a routine basis. Some discoloration of the finish may occur when a door has been exposed to dirt-laden atmosphere for a period of time. Slight chalking may also occu ...

  • Wayne-Dalton 9800 - page 17

    W ARNING W ARNING NEVER REMOVE, ADJUST , OR LOOSEN THE BOL TS, SCREWS AND/OR LAG SCREWS ON THE COUNTERBALANCE (END OR CENTER BEARING BRACKETS) SYSTEM OR BO TTOM CORNER BRACKETS OF THE DOOR. THESE BRACKETS ARE CONNECTED TO THE SPRING(S) AND ARE UNDER EXTREME TENSION. TO AVOID POSSIBLE SEVERE OR FA T AL INJURY , HAVE ANY SUCH WORK PERFORMED BY A TRAI ...

  • Wayne-Dalton 9800 - page 18

    Limited Warranty Model 9800 Wayne Dalton, a division of Overhead Door Corporation (“Seller”) warrants to the original purchaser of the Model 9800 (“Product”), subject to all of the terms and conditions hereof, tha t the Product and all components thereof will be free from defects in materials and workmanship for the following period(s) of t ...

  • Wayne-Dalton 9800 - page 19

    ...

  • Wayne-Dalton 9800 - page 20

    AFTER INST ALLA TION IS COMPLETE, F ASTEN THIS MANUAL NEAR GARAGE DOOR FOR EASY REFERENCE. PLEASE DO NO T RETURN THIS PRODUCT TO THE STORE Thank you for your pur chase. Please Do Not Return This Product T o The Store. Please call 1-866-569-3799 (Press Option 1) and follow the prompts to contact the appropriate customer ser vice agent. They will be ...

メーカー Wayne-Dalton カテゴリー Garage Door Opener

Wayne-Dalton 9800のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 9800の取扱説明書
- Wayne-Daltonの製品カード
- パンフレット
- またはWayne-Dalton 9800の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Wayne-Dalton 9800の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Wayne-Dalton 9800の取り付け説明書、サービスマニュアル、簡易説明書、またはWayne-Dalton 9800のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Wayne-Dalton 9800の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Wayne-Dalton 9800デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWayne-Dalton 9800を使用するのを助ける技術的文書のことです。説明書は通常、全てのWayne-Dalton 9800ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Wayne-Daltonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Wayne-Dalton 9800の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWayne-Dalton 9800の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Wayne-Dalton 9800に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Wayne-Dalton 9800デバイスの基本機能を使うにあたってのヒント。 Wayne-Dalton 9800のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Wayne-Dalton 9800に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWayne-Dalton 9800のメーカー/サービスへの連絡先に関する情報。

Wayne-Dalton 9800についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWayne-Dalton 9800の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWayne-Dalton 9800で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)