-
Scytek electronic 2000RS - page 1
GALAXY 5000RS/2000RS SERIES-DBP DATA BUS PORT VEHICLE SECURITY SYSTEM WITH REMOTE START PRODUCT MANUAL ...
-
Scytek electronic 2000RS - page 2
L i m i t e d L i f e t i m e W a r r a n t y This vehicle security system is warranted to the original purchaser , to be free from defects in material and workmanship. The manufacturer will rep air or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal i ...
-
Scytek electronic 2000RS - page 3
1. About Y our System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 2. Remote T r ansmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P age 2 Remote T r ansmitter Description . . . . . . . . . . . . . . . . . . . . ...
-
Scytek electronic 2000RS - page 4
...
-
Scytek electronic 2000RS - page 5
The ScyT ek Galaxy 5000RS-DBP Series is a Combination Vehicle Security and Remote Starting System , Galaxy 2000RS-DBP Series is a Remote Starting with keyless entry . featuring a built -in "ScyNet Network Port" that allows direct connection of optional accessory modules and a PC interface off ering expanded system operation. With proper i ...
-
Scytek electronic 2000RS - page 6
Standard Remote Transmitter Description Depending on the model chosen, the Galaxy 5000/2000RS-DBP Series will be supplied with one or two T5 or T5-SP 5-button R emote T ransmitters that are used to control the system’ s operations. Note : Using the optional PC or P ocket PC interface with the network softw are, it is possible to reconfigure the f ...
-
Scytek electronic 2000RS - page 7
Adding/Replacing Standard Remote Transmitters T o replace lost or stolen tr ansmitters or to add additional transmit ters into the system, have all desired transmit ters ready and follow the steps below . Note : Up to 4 one-wa y transmitters can be progr ammed to operate the system. An y previously stored transmit ter will be erased if it is not pr ...
-
Scytek electronic 2000RS - page 8
2-way LCD Remote Transmitter Description Depending on the model chosen, the Galaxy 5000/2000RS-DBP-2W Series will be supplied with one or two 2-way LCD R emote T ransmitters, of fering increased range and confirmation of an y activated f eatures. Page 1 Button 1 Arms and Locks the system and when held for 5 seconds, activ ates the system’ s Panic ...
-
Scytek electronic 2000RS - page 9
· The LED will illuminate. 3. Press and release Button 1 on the first tr ansmitter then on the second transmit ter . · The siren/horn will chirp/honk once for every tr ansmitter learned. 4. T urn off the ignition k ey . 5. The siren/horn will chirp/honk 3 times to indicate the system has exited programming mode. LCD Transmitter Battery Replacemen ...
-
Scytek electronic 2000RS - page 10
T o set the daily start feature: 1. Press and hold Buttons 2 and 3 until the remote beeps four times. · The fan and clock will be shown indicating daily start mode is entered. 2. Press Button 2 until the desired hour is displayed. 3. Press Button 3 until the desired minute is displayed. The but ton may be held down to scroll faster . 4. When the d ...
-
Scytek electronic 2000RS - page 11
Galaxy 5000/2000RS-DBP - Page 7 CHP Set the siren/horn confirmation chirps/honks ON or OFF : 1. Press and hold Button 5 until the display shows CHP . ·The transmit ter will beep three times. 2. Release But ton 5. · The transmit ter will beep once. · The LCD panel will show a siren if the chirps*/honks are enabled or "off " if the chirp ...
-
Scytek electronic 2000RS - page 12
Page 8 - Galaxy 5000/2000RS-DBP ...
-
Scytek electronic 2000RS - page 13
Galaxy 5000/2000RS-DBP - Page 9 Button 1 Button 2 Button 3 Button 4 Button 5 11/16 3:10P Battery status wakeu p alarm enabled autostart enabled date/engine run timer time Optional 2-wa y Color remote transmitter is off ering increased range and confirmation of any activ ated feature. Page 1 Button 1 Arms and Locks* the system and when held for 3 se ...
-
Scytek electronic 2000RS - page 14
Page 10 - Galaxy 5000/2000RS-DBP Press and hold Buttons 2 and 3 until pager progr am features are displayed. Select pager setting by pressing buttons 1 or 2 to highlight the remote pager . Press button 3 to select the pager . Setting Date & Time Select Time Date setting by pressing buttons 1 or 2 to highlight the f eature. Press button 3 to sel ...
-
Scytek electronic 2000RS - page 15
Galaxy 5000/2000RS-DBP - Page 11 Use buttons 1 & 2 to highlight the time par ameter you wish to change, use buttons 3 & 4 to scroll up or down to chage the time. Save the changes by pressing but ton 5. Setting Alarm Clock Select Alarm setting by pressing buttons 1 or 2 to highlight the f eature. Press button 3 to select it. Enable/Disable A ...
-
Scytek electronic 2000RS - page 16
Page 12 - Galaxy 5000/2000RS-DBP Return to Previous Screen Select Previous Screen by pressing buttons 1 or 2 to highlight the feature. Press but ton 3 to select it. Press and hold Buttons 2 and 3 until pager progr am features are displayed. Select system setting by pressing buttons 1 or 2 to highlight the siren. Press but ton 3 to select the system ...
-
Scytek electronic 2000RS - page 17
Galaxy 5000/2000RS-DBP - Page 13 Setting AutoStart Cold Temperature Threshold Select Cold T emp start setting by pressing but tons 1 or 2 to highlight the feature. Press button 3 to select it. Use buttons 3 & 4 to scroll up or down to chage the temper ature threshold. Save the changes by pressing button 5. Setting AutoStart Hot Temperature Thre ...
-
Scytek electronic 2000RS - page 18
Page 14 - Galaxy 5000/2000RS-DBP Select Clock Sync set ting by pressing buttons 1 or 2 to highlight the arrows. Press button 3 to select the pager . Pager Clock Sync This feature synchronizes the pager clock to the security system time of a da y clock. Select P ager Clock Sync by pressing buttons 1 or 2 to highlight the f eature. Press button 3 to ...
-
Scytek electronic 2000RS - page 19
Galaxy 5000/2000RS-DBP - Page 15 Use buttons 1 & 2 to highlight Set Time press button 3. The security system responce. Start Time 2 This feature sets the system Autostart 2 time. Select Sytem Clock S ync by pressing buttons 1 or 2 to highlight the feature. Press but ton 3 to select it. Use buttons 1 & 2 to highlight hours or minutes, use bu ...
-
Scytek electronic 2000RS - page 20
Page 16 - Galaxy 5000/2000RS-DBP Pressing and holding transmit ter button 5 will scroll through sever al transmitter progr ammable options - TEMPERATURE, ENABLE COLD START, ENABLE HOT START, VALET MODE, ENABLE AUTOSTART 1, ENABLE AUTOSTART 2. TEMPERATURE Check the temperature inside the vehicle 1. Press and hold Button 5 until the display shows TEM ...
-
Scytek electronic 2000RS - page 21
Galaxy 5000/2000RS-DBP - Page 17 Transmitter Lockout Press and hold buttons 2 & 4 simultanously for 3 seconds to lockout the tr ansmitter against accidental transmission. Release Transmitter Lockout Press and hold buttons 2 & 4 simultanously for 3 seconds to release the transmit ter from Lockout. Out of Range Report pager report if no respo ...
-
Scytek electronic 2000RS - page 22
Page 18 - Galaxy 5000/2000RS-DBP P P a a g g e e r r S S t t a a t t u u s s D D i i s s p p l l a a y y Time: time of day clock Date/Engine Run Timer: date, or engine run minute timer if remote start activated (20 min max). Battery Status: displays remaining battery life. Wakeup Alarm: displays W akeup alarm enabled Autostart: Remote Start Autosta ...
-
Scytek electronic 2000RS - page 23
Galaxy 5000/2000RS-DBP - Page 19 Remote Arming/Locking The system monitors 5 independent areas ( zones ) while armed: doors, hood/ trunk, shock sensor , optional sensor input, and the network port for future expansion. T o Arm and Lock the S ystem: 1. T urn off the ignition. 2. Press Button 1. · The siren/horn will chirp/honk once. · The doors wi ...
-
Scytek electronic 2000RS - page 24
Page 20 - Galaxy 5000/2000RS-DBP Tamper Alert If the system was triggered while awa y , the LED will flash to indicate which zone triggered the system after disarming and turning the ignition ON. The LED indication will repeat 8 times. LED Flashes (60 seconds): 1 flash = optional sensor 2 flashes = shock sensor 3 flashes = network based sensor 4 fl ...
-
Scytek electronic 2000RS - page 25
Galaxy 5000/2000RS-DBP - Page 21 Panic Mode In the event of an emergency , the transmit ter’s remote P anic feature can be used to instantly trigger the alarm/panic feature. T o activ ate the Panic Mode: 1. Press and hold Button 1 for fiv e seconds. · The alarm will sound. · The parking lights will flash. · The doors will unlock** allowing acc ...
-
Scytek electronic 2000RS - page 26
Page 22 - Galaxy 5000/2000RS-DBP 3. Press the valet switch 4 times. · The siren will chirp each time the valet switch is pressed. 4. Within 5 seconds, press Button 3 on the tr ansmitter . · The siren will chirp 3 times. 5. Press the valet switch the number of times equal to the desired code (from 1-15). 6. T urn off the ignition then arm the syst ...
-
Scytek electronic 2000RS - page 27
Galaxy 5000/2000RS-DBP - Page 23 Remote Starting T o R emote Start the System: 1. Be sure the system is not in V alet Mode. 2. Press and hold Button 4 for three seconds. · The parking lights will flash 4 times and turn on. · The siren/horn will chirp/honk 4 times. ( if enabled, see page 23 branch 9 ) · The engine will start and run for the dur a ...
-
Scytek electronic 2000RS - page 28
Page 24 - Galaxy 5000/2000RS-DBP Automatic Start Mode Automatic Start feature has three modes that will start the vehicle every one or two hours within a 24 hour period. 1. Timer Only Mode (factory def ault) The Automatic Start feature starts the vehicle automatically ev ery one or two hours and runs for the preset Run Time. (15 or 25 min) Auto Sta ...
-
Scytek electronic 2000RS - page 29
Galaxy 5000/2000RS-DBP - Page 25 Model: Galaxy 5000/2000RS-DBP-M 1- T ach wire must be connected , The system must learn RPM. 2- Hand brak e must be connected. 3- Door trigger must be connected 4- Clutch override installed NOTE: MUST USE RELAY, SEE PAGE 26. Remote Starting With engine running and Hand-brak e engaged put the vehicle transmission in ...
-
Scytek electronic 2000RS - page 30
Page 26 -Galaxy 5000/2000RS-DBP E x t e n d e d F e a t u r e s Ignition Door Locking F or added safety , the Ignition Door Locking f eature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. If a door is open when the ignition is turned on, the Ignition Door Locking feature is disa ...
-
Scytek electronic 2000RS - page 31
Galaxy 5000/2000RS-DBP - Page 27 1. Thoroughly read and become familiar with the installation instructions bef ore beginning the installation. 2. R eview system contents: Main Unit 1 or 2 One-wa y 5 Button Remote T ransmitters (v aries by model) 1 or 2 T wo-wa y 5 Button LCD R emote T ransmitters (v aries by model) Siren Shock Sensor Harnesses • ...
-
Scytek electronic 2000RS - page 32
Page 28 - Galaxy 5000/2000RS-DBP Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thief , and will not interfere with the oper ation of any vehicle components such as f oot pedals, s ...
-
Scytek electronic 2000RS - page 33
Galaxy 5000/2000RS-DBP - Page 29 S y s t e m W i r i n g 6-Pin Starter Harness Pin 1 RED WIRE A : Main P ower Input A (+). Connect to the battery or constant power wire at the ignition switch with a minimum 25 Amp supply . R emo v e the f use until the installation is complete and all wiring is check ed. Pin 2 RED WIRE B : Main Power Input B (+). C ...
-
Scytek electronic 2000RS - page 34
Page 30 - Galaxy 5000/2000RS-DBP Pin 12 GREEN WIRE : Negative Door Input (-). Connect to the door switch circuit wire that shows ground when the door is open. Pin 13 WHITE/BLACK WIRE : Hood/T runk Pin Input (-). Connect the to the hood/trunk pin switch. The switch must provide a ground output when switch is opened. Pin 14 ORANGE WIRE : Armed Output ...
-
Scytek electronic 2000RS - page 35
Galaxy 5000/2000RS-DBP - Page 31 2-Pin White Connector: Located on the side of the main module. · Green WIRE - Parking Br ake Input (-) Fo r Manual T r ansmission and/or vehicles equipped with a turbo charged engine. Must be connected if using the T urbo Timer feature and/or Manual T ransmission remote start feature. · Blue WIRE - T urbo Timer ca ...
-
Scytek electronic 2000RS - page 36
Page 32 - Galaxy 5000/2000RS-DBP Entering System Programming This system is compatible with both the LCD two wa y transmitter or the standard tr ansmitter , all system programming can be perf ormed using either one. T o enter S ystem Programming: 1. T urn the ignition switch to the ON position. 2. Within 5 seconds, press the valet switch 5 times. ? ...
-
Scytek electronic 2000RS - page 37
Galaxy 5000/2000RS-DBP - Page 33 5. Ignition Door Unlocking. Selects whether or not the system automatically unlocks the doors when the ignition is turned off . The Ignition Door Locking feature may be progr ammed to unlock all doors or the driver’ s door only . If driver’s door only is selected, the optional P assenger Unlock wire must be conn ...
-
Scytek electronic 2000RS - page 38
Page 34 -Galaxy 5000/2000RS-DBP 6. Door Unlock Pulse. Selects between one pulse or two pulse operation for the door unlock output. Many new import vehicles’ f actory door locking systems require two pulses on the proper wire to unlock the doors. These systems can be interfaced directly without the use of relays or an y additional circuitry by pro ...
-
Scytek electronic 2000RS - page 39
Galaxy 5000/2000RS-DBP - Page 35 16. Auxiliary 3 Output Mode. Selects between Channel 3, F actory Rearm output, or third I gnition ouput. 17 . Lock After Start. When selected, the doors will automatically lock after remote starting. Using button 3 disabled Mp Siren Mode . 18. Lock After Shutdown. When selected, the doors will automatically lock aft ...
-
Scytek electronic 2000RS - page 40
Page 36 - Galaxy 5000/2000RS-DBP 28. Siren Mode. Selects standard siren (defualt) or MP Player Siren. 29. Turbo Timer. When enabled, if the emergency brake has been applied Ignition power will be k ept On for a predetermined time (2 minutes F actory Default) from the application of the emergency br ake. 30. Extended Parking Lights. When Enabled, up ...
-
Scytek electronic 2000RS - page 41
Galaxy 5000/2000RS-DBP R e l a y D i a g r a m s P ositive Dome Light Activ ation Negative Dome Light Activ ation P ositive Horn Honk Negative Horn Honk Starter Defeat/Anti-Grind Negative Glow Plug ...
-
Scytek electronic 2000RS - page 42
Page 38 - Galaxy Negative T rigger R everse P olarity V acuum Adding Actuators F ollow the diagrams below for connecting basic door lock systems. F or T wo Stage door lock systems (separately unlocks driv er and passenger doors) see following pages. D o o r L o c k D i a g r a m s P ositive T rigger UL L blue green ...
-
Scytek electronic 2000RS - page 43
Galaxy 5000/2000RS-DBP T w o S t a g e D o o r L o c k D i a g r a m s T wo Stage Negative T rigger T wo Stage P ositive T rigger The Galaxy 5000/2000RS-DBP Series is equipped with a dedicated P assenger Unlock output allowing T wo Stage Door Lock operation. When connected as shown below , disarming the system will unlock only the driver’ s door ...
-
Scytek electronic 2000RS - page 44
Page 40 - Galaxy 5000/2000RS-DBP T w o S t a g e D o o r L o c k Diagrams c o n t ’ d T wo Stage R everse P olarity T wo Stage Adding Actuators ...
-
Scytek electronic 2000RS - page 45
Galaxy 5000/2000RS-DBP - Page 41 FCC ID: OARRXAM2000 This device complies with P art 15 of FCC Rules. Operation is subject to the f ollowing two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interf erence that may cause undesired operation T e c h n i c a l I n f o r m ...
-
Scytek electronic 2000RS - page 46
Page 42 - Galaxy 5000/2000RS-DBP S t a r t e r D i a g n o s t i c s Starter doesn’t start and parking lights flash: 3 Times - Engine RPM not detected (check tach wire and/or perform tach learn procedure) Hood Trigger is active (hood is open, wire is shorted to ground or pin switch is defective) 4 Times - Brake Trigger is active ( Brake switch in ...
-
Scytek electronic 2000RS - page 47
Galaxy 5000/2000RS-DBP - Page 43 Shock Sensor Adjustment: Clock wise increases sensitivity S h o c k S e n s o r A d j u s t m e n t ...
-
Scytek electronic 2000RS - page 48
ScyTek Electronics 11627 Cantara Street North Hollywood, CA 91605 www .scytek.net © ScyT ek Electronics 2010 Galaxy DBP 10-19-10 W i r i n g D i a g r a m ScyNet Blue Aux S tart (-) / T urbo T imer Cancel Green Emergency brake(-) Antenna Shock Sensor Port LED Port Valet Switch Port Door Lock Port Main Harness Starter Harness Green Lock output (-) ...
Do you have a question concerning Scytek electronic 2000RS?
Use the form below
If you did not solve your problem by using a manual Scytek electronic 2000RS, ask a question using the form below. If a user had a similar problem with Scytek electronic 2000RS it is likely that he will want to share the way to solve it.