English dropdown-ico

Manual Pelco MPT9000PZ

32 pages 0.4 mb
Download

Go to site of 32

Summary
  • Pelco MPT9000PZ - page 1

    ® MPT9000CZ/ MPT9000PZ T ransmitter/ Contr ol (Coaxitron ® System 2000) Installation/ Operation Manual C550M-E (8/97) Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150 International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120 ...

  • Pelco MPT9000PZ - page 2

    TABLE OF CONTENTS Section Page 1.0 WARNING .......................................................................................................................................... 1 2.0 SCOPE ............................................................................................................................................... 2 3.0 DESCRI ...

  • Pelco MPT9000PZ - page 3

    LIST OF ILLUSTRATIONS Figure Page 1 Coaxitron System 2000 Receiver ................................................................................................ ... 3 2 24 VAC Input Wiring Schematic ................................................................................................. .... 3 3 AC Input and Fuse Values ................ ...

  • Pelco MPT9000PZ - page 4

    REVISION HISTORY Manual # Date Comments C550M — Original version. C550M 8/89 Rev. A. Manual revised to new format. C550M 9/90 Rev. B. Manual revised to include 230 VAC, 12 V and preset (PP) models. Sections 2.1-2.3, 4.1.1, 4.2 and 5.5- 5.6 revised. C550M 5/91 Rev. C. New figure added for connector assembly (Fig. 2); Figure 16 revised. C550M 6/92 ...

  • Pelco MPT9000PZ - page 5

    Pelco Manual C550M-E (8/97) 1 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 4. Only use replacement parts recommended by Pelco. 5. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to verify the exposed pa ...

  • Pelco MPT9000PZ - page 6

    2 Pelco Manual C550M-E (8/97) NOTE: This manual applies to those Coaxitron systems using either PCB1500529 REV J or PCB1500529 REV K boards. PCB board draw- ings were done from the REV J board perspective; however, differences between the two boards that affect function or operation are clearly pointed out. 2.0 SCOPE The information contained withi ...

  • Pelco MPT9000PZ - page 7

    Pelco Manual C550M-E (8/97) 3 Figure 1. Coaxitron System 2000 Receiver Figure 2. 24 VAC Input Wiring Schematic T1 T2 T3 POWER INPUT PC BOARD SCREWS SCREWS AMP CONNECTOR 37-PIN Remove PC board mounting screws and remove the PC board. If necessary, tag and remove the PC board. REMOVE POWER CORD COAXITRON SYSTEM 2000 RECEIVER Remove or loosen the four ...

  • Pelco MPT9000PZ - page 8

    4 Pelco Manual C550M-E (8/97) Figure 3. AC Input and Fuse Values shown in the "Short" position 37-PIN AMP CONNECTOR POWER INPUT PC BOARD 1. AC HIGH 2. GROUND 3. AC LOW F2 F3 TRANSMITTER: F1 2/10 ASB, 3AG shown in the "Long" position AC INPUT DESIGNATIONS FUSES RECEIVER FUSE VALUES: SHOWN BELOW F1 BNC CONNECTORS P2 P1 SW 1 SW 1 * ...

  • Pelco MPT9000PZ - page 9

    Pelco Manual C550M-E (8/97) 5 4. The contact pins supplied with the mating con- nector are the “crimp” type which may also be soldered if you so desired (item 4). 5. After crimping or soldering the contact pins to the conductors, push them into the proper holes in the connector until they snap in place. Note: Contacts cannot be removed from the ...

  • Pelco MPT9000PZ - page 10

    6 Pelco Manual C550M-E (8/97) Figure 5. Receiver Control Output/Input Pin Assignments shown in the "Short" position 37-PIN AMP CONNECTOR POWER INPUT PC BOARD SW 1 P2 P1 BNC CONNECTORS COAXITRON SYSTEM 2000 RECEIVER P1 3 BRN P/T COM 1 5 ORG LEFT 3 8 4 7 GRN DOWN 5 6 BLU UP 6 4 VIO RIGHT 7 9 GRA Y GROUND 8 12 BLACK IRIS 10 1 1 1 W/BRN FOCUS ...

  • Pelco MPT9000PZ - page 11

    Pelco Manual C550M-E (8/97) 7 Figure 7. Coaxitron System 2000 with Manual Video Switcher and Multiple Cameras Figure 6. Basic Coaxitron System 2000 4.3 SYSTEM CONFIGURATIONS Figure 6 shows the simplest system configuration utiliz- ing the Coaxitron System 2000. This system consists of the control transmitter, coax cable and receiver/camera. This ba ...

  • Pelco MPT9000PZ - page 12

    8 Pelco Manual C550M-E (8/97) A more complex system is shown in Figure 8. Here, several control locations can serve a single camera system. Note : All transmitters, except the last one, must be looping (unterminated) rather than terminating. In a system of this type, any one of the transmitters can assume control because there is no priority provis ...

  • Pelco MPT9000PZ - page 13

    Pelco Manual C550M-E (8/97) 9 Figure 9. Coaxitron System 2000 with Multiple Transmitters and Receivers Figure 10. Coaxitron System 2000 Basic Interconnect Diagram AC INPUT F1 .2 ASB 120 V AC 230 V AC LOOPING OUTPUT INPUT FROM RECEIVER OUTPUT TO MONITOR J8 J7 J6 VIDEO TO ADDITIONAL CONTROL TRANSMITTERS OR TERMINA TE TRANSMITTER VIDEO CABLE RECEIVER ...

  • Pelco MPT9000PZ - page 14

    10 Pelco Manual C550M-E (8/97) 5.0 OPERATION In general, all operating controls on the transmitter are self explanatory. With the exception of the ON/OFF power switch and the 8-position joystick, all controls are center-off, spring return paddle switches (momen- tary on-off-on). 5.1 FUNCTIONAL CIRCUIT DESCRIPTION The basic functional concept of the ...

  • Pelco MPT9000PZ - page 15

    Pelco Manual C550M-E (8/97) 11 As an example, assume that the operator switches to manual iris control and proceeds to open the iris exces- sively. The result can be a complete loss of control. Within 20 to 40 seconds, camera power is automatically removed (assuming this feature exists) and auto iris is reinstated. Thus, distortion products are eli ...

  • Pelco MPT9000PZ - page 16

    12 Pelco Manual C550M-E (8/97) • Receiver Control Output for 12 VDC Camera Option The usual output for camera power is 24 VAC accessed at pins 9 and 14 of the 37-pin AMP connector (see Fig. 5) where CAM AC HIGH and AC LOW emerge as CAMERA INPUT POWER. The output pin assignments remain the same for 12 VDC camera power options, only now pin 9 (WH) ...

  • Pelco MPT9000PZ - page 17

    Pelco Manual C550M-E (8/97) 13 Up to 32 presets can be stored in each receiver. Up to 8 presets can be activated by alarm contacts connected to the receiver. There is also an open collector output from the receiver to activate an external device (such as the CSA764) when the alarm contacts are activated. Figure 11 shows the wiring for alarmed prese ...

  • Pelco MPT9000PZ - page 18

    14 Pelco Manual C550M-E (8/97) SB1900-PP , SB1900SL-PP , SS2000-PP and SS2000SL-PP 37-pin Connector Function Function 37-pin Connector 28-pin Connector Function 1 Pan/T ilt Common 1 Pan/T ilt Common 1 Pan/T ilt Common 2 Manual Iris 2 Not Used 2 Video Core 3 Pan Left 3 Pan Left 3 Pan Left 4 Video Shield 4 Video Shield 4 Video Shield 5 T ilt Down 5 T ...

  • Pelco MPT9000PZ - page 19

    Pelco Manual C550M-E (8/97) 15 37-pin Connector Function Function 37-pin Connector 28-pin Connector Function 1 Pan/T ilt Common 1 Pan/T ilt Common 1 Pan/T ilt Common 2 Manual Iris 2 Preset Pan 2 Video Core 3 Pan Left 3 Pan Left 3 Pan Left 4 Video Shield 4 Video Shield 4 Video Shield 5 T ilt Down 5 T ilt Down 5 T ilt Down 6 T ilt Up 6 T ilt Up 6 T i ...

  • Pelco MPT9000PZ - page 20

    16 Pelco Manual C550M-E (8/97) Preposition Lenses 37-pin 9-pin Connector Function Connector Function 1 Pan/Tilt Common 1 Iris 2 Manual Iris 2 Zoom 3 Pan Left 3 Focus 4 Video Shield 4 Lens Common 5 Tilt Down 5 Ground 6 Tilt Up 6 Preset +5V 7 Pan Right 7 Preset Zoom 8 Ground 8 Preset Ground 9 Camera AC (High) 9 Preset Focus 10 Iris 11 Focus 12 Zoom 1 ...

  • Pelco MPT9000PZ - page 21

    Pelco Manual C550M-E (8/97) 17 5.6 AUXILIARY FUNCTIONS The Coaxitron receiver is capable of operating up to four (4) remotely activated auxiliary functions. Each auxiliary output may be individually converted at the receiver for momentary or latching operation. Refer to Figure 15 for the desired jumper location. When in the latching mode, activatin ...

  • Pelco MPT9000PZ - page 22

    18 Pelco Manual C550M-E (8/97) Figure 16. External Device Wiring Diagram 1 2 3 8 MANUAL IRIS GROUND CONNECT TO NEGATIVE SIDE OF 12 VDC SUPPLY NOTE: CUSTOMER SUPPLIES PARTS AND 12 VDC POWER SUPPLY + 12 VDC NORMALLY-OPEN CONTACTS 10 VDC RELAY 25 mA COIL CURRENT MAXIMUM 1N4005 COAXITRON RECEIVER/DRIVER 37-PIN CONNECTOR ...

  • Pelco MPT9000PZ - page 23

    Pelco Manual C550M-E (8/97) 19 Figure 17. Auxiliary Functions Wiring Diagram 30 34 33 32 36 RECEIVER/DRIVER 37-PIN CONNECTOR AUXILIARY FUNCTIONS TYPICAL WIRING CONNECTIONS 10 VDC RELAY 25 mA COIL CURRENT MAXIMUM 10 VDC RELAY 25 mA COIL CURRENT MAXIMUM 10 VDC RELAY 25 mA COIL CURRENT MAXIMUM 1N4005 1N4005 1N4005 10 VDC RELAY 25 mA COIL CURRENT MAXIM ...

  • Pelco MPT9000PZ - page 24

    20 Pelco Manual C550M-E (8/97) Figure 18. AI700/AI701 Wiring Diagram 1 2 3 10 11 12 13 MANUAL IRIS COAXITRON RECEIVER 37 PIN CONNECTOR IRIS FOCUS ZOOM LENS COMMON 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 LENS CABLE LENS CABLE TO COAXITRON RECEIVER COAX COAX AUX 1 COMMAND LATCHES MANUAL IRIS CONTROL AUX 2 COMMAND LATCHES AUTO/IRIS CONTROL CAMERA LENS ...

  • Pelco MPT9000PZ - page 25

    Pelco Manual C550M-E (8/97) 21 Figure 19. Coaxitron Receiver Assembly Layout (Top View) 5.7 AUTO/RANDOM OPERATION The A9000 Auto/Random Scan module is a plug-in P.C. board option (See Fig. 19 for board location) for all Coaxitron receivers. This module provides two modes for automatically controlling pan and tilts within preset limits — Auto Scan ...

  • Pelco MPT9000PZ - page 26

    22 Pelco Manual C550M-E (8/97) Figure 20. A9000 Wiring Schematic U1 1N914 1 2 8 3 R1 100K +10 GND ACTIVE 14 15 U1 CD4049 U1 U1 U1 U1 R2 820 LED 1 12 10 6 4 11 9 7 5 AUTO SCAN CAM ON AUX 4 AUTO IRIS AUX 2 IRIS CLOSE FOCUS NEAR ZOOM WIDE DOWN RIGHT LEFT UP ZOOM TELE FOCUS FAR IRIS OPEN AUX 1 MAN IRIS AUX 3 CAM OFF MAN SCAN S1 S2 S3 S4 S5 S6 S7 S8 S9 ...

  • Pelco MPT9000PZ - page 27

    Pelco Manual C550M-E (8/97) 23 Figure 21. CX900TLC Test Module and Wiring Schematic 6.0 TROUBLESHOOTING GUIDELINES If you experience operating problems with either the receiver or transmitter, first check all fuses and voltage readings to make sure they are in working order. The CX900TLC can be utilized to verify receiver functions and accessories ...

  • Pelco MPT9000PZ - page 28

    24 Pelco Manual C550M-E (8/97) 8.0 MODEL NUMBER TRANSMITTER WEATHER-PROOF? INDOOR USE? 24VAC PAN/TILT? 120VAC PAN/TILT? 230VAC PAN/TILT? Receiver in weatherproof box, 120VAC power input, 24VAC pan/tilts with power supply for pan/tilt, zoom lens, and 4 accessory functions (3 latching, 1 momentary). CX9024RX 24VAC POWER INPUT? CX9224RX Same as CX9024 ...

  • Pelco MPT9000PZ - page 29

    Pelco Manual C550M-E (8/97) 25 8.1 OPTIONAL ACCESSORIES A9000 Auto/random scan, plug-in mod- ule. AUX2000 Auxiliary function relay box for control of wiper/washer functions. AUX9000 Auxiliary function wiring harness. Required for use with AUX2000 and all indoor Coaxitron/Wiretron receivers (supplied with outdoor receivers). CX900TLC Local test boar ...

  • Pelco MPT9000PZ - page 30

    26 Pelco Manual C550M-E (8/97) Input Video Level: 1V p-p nominal; 2V p-p maxi- mum at less than 75% APL; 1.5V p-p maximum at 90% APL System Bandwidth: Less than 2 dB down at 10 MHz (exclusive of cable) Fuse Protection: 3 AG type Power Cord: 3-wire grounded #18 AWG, Transmitter and Receiver Operating Distance: Cable distances are approximate accordi ...

  • Pelco MPT9000PZ - page 31

    Pelco Manual C550M-E (8/97) 27 NOTES: ...

  • Pelco MPT9000PZ - page 32

    28 Pelco Manual C550M-E (8/97) 10.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three ...

Manufacturer Pelco Category Satellite Radio

Documents that we receive from a manufacturer of a Pelco MPT9000PZ can be divided into several groups. They are, among others:
- Pelco technical drawings
- MPT9000PZ manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco MPT9000PZ
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco MPT9000PZ.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco MPT9000PZ, service manual, brief instructions and user manuals Pelco MPT9000PZ. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco MPT9000PZ.

Similar manuals

A complete manual for the device Pelco MPT9000PZ, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco MPT9000PZ by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco MPT9000PZ.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco MPT9000PZ - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco MPT9000PZ, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco MPT9000PZ, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco MPT9000PZ - which should help us in our first steps of using Pelco MPT9000PZ
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco MPT9000PZ
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco MPT9000PZ in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco MPT9000PZ?

Use the form below

If you did not solve your problem by using a manual Pelco MPT9000PZ, ask a question using the form below. If a user had a similar problem with Pelco MPT9000PZ it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)