English dropdown-ico

Manual Axxess Interface Automobile Accessories

12 pages 0.83 mb
Download

Go to site of 12

Summary
  • Axxess Interface Automobile Accessories - page 1

    © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORA TION 1-800-221-0932 axxessinterf ace.com INST ALLA TION INSTRUCTIONS FOR PART RF ASWC The RF ASWC is designed for adding steering wheel controls to vehicles that do not have OE steering wheel controls installed. With Aftermarket radio’s with steering wheel control outputs the RF ASWC is able to giv ...

  • Axxess Interface Automobile Accessories - page 2

    Mounting The RF ASWC T ransmitter 1. Place button pad in the OESWC transmitter with the volume up arrow (^) in the spot where you want volume up to be.(g. 1) 2. Snap in trim ring to secure keypad in place. (g. 2) 3. Install the OESWC transmitter in desired place on steering wheel, wrapping the rubber strap around the steering wheel, through t ...

  • Axxess Interface Automobile Accessories - page 3

    Wiring The OESWC Interface 1. Connect the red wire to 12 volt accessory 2. Connect the Black wire to ground (you may use the same ground that you use for the aftermarket radio) If you are using an Eclipse or Kenwood radio, plug the female 3.5mm connector with the Brown and Brown/White wires into the male 3.5mm connector of the ASWC harness. * For K ...

  • Axxess Interface Automobile Accessories - page 4

    2. T urn on the ignition and press volume up on the RF ASWC. This will “marry“ the RF ASWC to the interface. NOTE: If you are replacing a transmitter you must turn on the ignition and within the rst 10 seconds press and hold the source button for ten seconds. This will “marry the new transmitter . Programming the RF ASWC 1. Complete connec ...

  • Axxess Interface Automobile Accessories - page 5

    5. The led will then ash up to 10 times. 6. This is the end of the auto detection stage. If the RF ASWC detected the radio successfully the led will light up solid red. 7. Make sure the steering wheel control buttons function correctly in the vehicle and enjoy your radio. So what if the led does not light up solid red? Check out troubleshooting ...

  • Axxess Interface Automobile Accessories - page 6

    Once all the information above has been veried and correct, refer back to the 2 sets of led ashes during the auto detect sequence. Here is what the ashes stand for: LED Feedback The led ashes represent what brand radio the RF ASWC believes it is connected to. Each ash is for a different radio manufacturer . For example you installed ...

  • Axxess Interface Automobile Accessories - page 7

    Remapping the SWC Buttons Let’s say you have the RF ASWC programmed to your radio and you want to change the button assignment for the steering wheel controls. For instance you would like Seek Up to be Mute. NOTES: • The RF ASWC must have detected the radio it is attached to before you can remap any buttons. • Y ou can only start the remappin ...

  • Axxess Interface Automobile Accessories - page 8

    5. Follow the list below in order however pushing the steering wheel control button you want for the function below . If you want to skip a command press the V olume Up on the steering wheel, this will tell the ASWC to skip the command and go to the next one. 1. V olume Up 2. V olume Down 3. Seek Up/Next 4. Seek Down/Prev 5. Source/Mode 6. Mute 7. ...

  • Axxess Interface Automobile Accessories - page 9

    * Note: Remember not all radios will have all these commands. Please refer to the radios’ owners manual for specic commands recognized by the radio. For instance the next command to be mapped is the V olume Down command. Let’s say you want the Mode button on your steering wheel to be the V olume Down command. Hold down the Mode button till t ...

  • Axxess Interface Automobile Accessories - page 10

    2. The led will turn on then release the V olume Down button and the led will turn off. 3. The original steering wheel control settings will be restored. Manually Setting The Radio T ype 1. Within the rst 20 seconds of turning the ignition on. Press and hold down the original V olume Down button (not the V olume Down button you just remapped) fo ...

  • Axxess Interface Automobile Accessories - page 11

    4. If you have a different radio then Eclipse, press the V olume Up button again till the led goes solid red, then release V olume Up. Y ou have now programmed Kenwood. 5. Here is the chart to show how many presses of the V olume Up button is needed for which radio you are trying to program: 1st led ash is for Eclipse 2nd led ash is for Kenwo ...

  • Axxess Interface Automobile Accessories - page 12

    REV . 1/10/1 1 1-800-221-0932 axxessinterf ace.com © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORA TION INST ALLA TION INSTRUCTIONS FOR PART RF ASWC K NO WLEDGE IS P OW ER E nhance your installation and fabrication skills by enrolling in the most re cognized and re spected mobile electronics school in our industry . Log onto www .installerinstitut ...

Manufacturer Axxess Interface Category Automobile Accessories

Documents that we receive from a manufacturer of a Axxess Interface Automobile Accessories can be divided into several groups. They are, among others:
- Axxess Interface technical drawings
- Automobile Accessories manuals
- Axxess Interface product data sheets
- information booklets
- or energy labels Axxess Interface Automobile Accessories
All of them are important, but the most important information from the point of view of use of the device are in the user manual Axxess Interface Automobile Accessories.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Axxess Interface Automobile Accessories, service manual, brief instructions and user manuals Axxess Interface Automobile Accessories. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Axxess Interface Automobile Accessories.

Similar manuals

A complete manual for the device Axxess Interface Automobile Accessories, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Axxess Interface Automobile Accessories by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Axxess Interface Automobile Accessories.

A complete Axxess Interface manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Axxess Interface Automobile Accessories - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Axxess Interface Automobile Accessories, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Axxess Interface Automobile Accessories, that we can find in the current document
3. Tips how to use the basic functions of the device Axxess Interface Automobile Accessories - which should help us in our first steps of using Axxess Interface Automobile Accessories
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Axxess Interface Automobile Accessories
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Axxess Interface Automobile Accessories in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Axxess Interface Automobile Accessories?

Use the form below

If you did not solve your problem by using a manual Axxess Interface Automobile Accessories, ask a question using the form below. If a user had a similar problem with Axxess Interface Automobile Accessories it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (1)

TimothyDep

Roller Door Servicing & Maintenance in Adelaide As with many mechanical devices, it is recommended that your garage door be serviced every 1-2 years depending on how frequently the door is used, environmental conditions etc. This helps prevent breakdowns and of course avoids inconvenience. Over time, springs lose tension, dirt and grime builds up in the guides, buildings move and motor parts wear. We’ll take the time to correctly service your door, as opposed to just fixing the problem. We gladly offer our customers a call back option where we will contact you when your door is next due for its service. A couple of things you can do to extend the life of your door include: Keep the tracks clean at all times Lubricate the tracks – this should NEVER be done with grease or oil! Only Silicon sprayed should be used – spray a little on the tracks and then wipe through with a clean rag. So... should you door be due (or overdue!) for some tender loving care, give our friendly team a call at Fast Fix Roller Doors and we will have you booked in within days and your door back up and running the way it should be! Call us today to arrange an appointment: (08) 8182 5787 <a href="http:/fastfixrollerdoors.com.au">doors</a>