Bedienungsanleitung Alvarez S408

19 Seiten 1.19 mb
Download

Zur Seite of 19

Summary
  • Alvarez S408 - page 1

    1 S408 REPAIR MANUAL S408 REPAIR MANUAL ...

  • Alvarez S408 - page 2

    2 These instructions are intended to help restore any ailing S408 Passive Loudspeaker back to factory working conditions. They show how to remove and replace the drivers. Please contact Mackie Technical Support (1-800-898-3211) to receive a Service Request Number and Order Number for parts needed for this restoration. They will also help you determ ...

  • Alvarez S408 - page 3

    3 Top left woofer replacement: 1 1 Six screws need to be removed from each side of the front of the grill (twelve screws total) using the phillips head screwdriver. This grill has a tendency to want to “pop” off, so please be sure to hold it in place with one hand or arm while removing the screws with your free hand. In addition to the grill, t ...

  • Alvarez S408 - page 4

    4 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Top left woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on the te ...

  • Alvarez S408 - page 5

    5 Top right woofer replacement: 2 2 Eight screws need to be removed from the woofer using the phillips head screwdriver. Once the screws are removed, the woofer may be loosened by prying a fl at head screwdriver in between the cabinet and the woofer; a good place to start is in the notches located just above the horn assembly and below the woofer ...

  • Alvarez S408 - page 6

    6 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Top right woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on the t ...

  • Alvarez S408 - page 7

    7 Bottom left woofer replacement: 2 2 Eight screws need to be removed from the woofer using the phillips head screwdriver. Once the screws are removed, the woofer may be loosened by prying a fl at head screwdriver in between the cabinet and the woofer; a good place to start is in the notches located just below the horn assembly and above the woofe ...

  • Alvarez S408 - page 8

    8 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Bottom left woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on the ...

  • Alvarez S408 - page 9

    9 Bottom right woofer replacement: 2 2 Eight screws need to be removed from the woofer using the phillips head screwdriver. Once the screws are removed, the woofer may be loosened by prying a fl at head screwdriver in between the cabinet and the woofer; a good place to start is in the notches located just below the horn assembly and above the woof ...

  • Alvarez S408 - page 10

    10 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Bottom right woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on t ...

  • Alvarez S408 - page 11

    11 High Frequency Driver replacement: 8 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 9 9 10 10 11 11 12 12 2 2 Twelve screws and fl at washers need to be removed from the horn assembly using the phillips head screwdriver. Once the screws are removed, the horn assembly may be loosened by prying a fl at head screwdriver in between the cabinet and the horn assembl ...

  • Alvarez S408 - page 12

    12 3 3 Carefully begin to remove the entire horn assembly (with the high frequency driver still attached). Caution: The horn weighs about 8 pounds, and the weight is unevenly distributed. High Frequency Driver replacement continued: 4 4 The positive (red and black) and negative (solid black) cables are still attached to the high frequency driver te ...

  • Alvarez S408 - page 13

    13 High Frequency Driver replacement continued: 6 6 Four bolts and eight washers may be removed from the driver using the 8mm combination wrench. Turn counter- clockwise to loosen and remove, clockwise to tighten. The other three are located around the horn assembly. Notice that the fl at washer is on the bottom, followed by the locking washer, an ...

  • Alvarez S408 - page 14

    14 3 3 The horn assembly is shown above with the high frequency driver circled. Four screws need to be removed from the driver using the 3mm allen wrench. 4 4 Keep the four screws in a safe place. 5 5 The diaphragm and plate adapter are easily removed from the horn assembly. Notice the terminal locations in relation to the indents of the high frequ ...

  • Alvarez S408 - page 15

    15 7 7 This is what the plate adapter (left) and diaphragm (right) both look like. Place the new diaphragm (part # coming soon) where the old one was. Follow the same steps as above, but backwards 6 to 1. Power up the S408 and the new diaphragm should now be pumping out those highs again. Sweet, you just replaced a diaphragm! Diaphragm replacement ...

  • Alvarez S408 - page 16

    16 Input assembly replacement: 1 1 Eight screws need to be removed from the input assembly (located on the rear of the cabinet) using the phillips head screwdriver. Once the screws are removed, the input assembly may be loosened by prying a fl at head screwdriver in between it and the cabinet. Keep the eight screws in a safe place. 1 1 2 2 3 3 4 4 ...

  • Alvarez S408 - page 17

    17 3 3 Two cables need to be removed from the input assembly PCB (as shown on the left and above): (1) the solid black cable attaches to the negative terminal (connection J4). This is for the input jack, and (2) the grey and black cable attaches to the positive terminal (connection J3). This is for the thru jack. Do not force cable removal or conne ...

  • Alvarez S408 - page 18

    18 Input assembly replacement continued: 4 4 Place the new input assembly (part #0012048) where the old one was. Follow the same steps as above, but backwards 3 to 1. Remove the serial number from the faulty input assembly (as shown in the picture above) and place on the new input assembly. Power up the S408 and relish in the fact that you just rep ...

  • Alvarez S408 - page 19

    19 This page left blank intentionally ...

Produzent Alvarez Kategorie Car Speaker

Dokumente, die wir vom Produzenten des Geräts Alvarez S408 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Alvarez
- Bedienungsanleitungen S408
- Produktkarten Alvarez
- Informationsbroschüren
- oder Energieetiketten Alvarez S408
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Alvarez S408.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Alvarez S408, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Alvarez S408. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Alvarez S408 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Alvarez S408, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Alvarez S408 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Alvarez S408 verständlich ist.

Eine gänzliche Bedienungsanleitung von Alvarez sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Alvarez S408 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Alvarez S408 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Alvarez S408, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Alvarez S408 - die uns die ersten Schritte während der Nutzung von Alvarez S408 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Alvarez S408 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Alvarez S408 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Alvarez S408?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Alvarez S408 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Alvarez S408 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)