Alvarez S408の取扱説明書

19ページ 1.19 mb
ダウンロード

ページに移動 of 19

Summary
  • Alvarez S408 - page 1

    1 S408 REPAIR MANUAL S408 REPAIR MANUAL ...

  • Alvarez S408 - page 2

    2 These instructions are intended to help restore any ailing S408 Passive Loudspeaker back to factory working conditions. They show how to remove and replace the drivers. Please contact Mackie Technical Support (1-800-898-3211) to receive a Service Request Number and Order Number for parts needed for this restoration. They will also help you determ ...

  • Alvarez S408 - page 3

    3 Top left woofer replacement: 1 1 Six screws need to be removed from each side of the front of the grill (twelve screws total) using the phillips head screwdriver. This grill has a tendency to want to “pop” off, so please be sure to hold it in place with one hand or arm while removing the screws with your free hand. In addition to the grill, t ...

  • Alvarez S408 - page 4

    4 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Top left woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on the te ...

  • Alvarez S408 - page 5

    5 Top right woofer replacement: 2 2 Eight screws need to be removed from the woofer using the phillips head screwdriver. Once the screws are removed, the woofer may be loosened by prying a fl at head screwdriver in between the cabinet and the woofer; a good place to start is in the notches located just above the horn assembly and below the woofer ...

  • Alvarez S408 - page 6

    6 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Top right woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on the t ...

  • Alvarez S408 - page 7

    7 Bottom left woofer replacement: 2 2 Eight screws need to be removed from the woofer using the phillips head screwdriver. Once the screws are removed, the woofer may be loosened by prying a fl at head screwdriver in between the cabinet and the woofer; a good place to start is in the notches located just below the horn assembly and above the woofe ...

  • Alvarez S408 - page 8

    8 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Bottom left woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on the ...

  • Alvarez S408 - page 9

    9 Bottom right woofer replacement: 2 2 Eight screws need to be removed from the woofer using the phillips head screwdriver. Once the screws are removed, the woofer may be loosened by prying a fl at head screwdriver in between the cabinet and the woofer; a good place to start is in the notches located just below the horn assembly and above the woof ...

  • Alvarez S408 - page 10

    10 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Bottom right woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on t ...

  • Alvarez S408 - page 11

    11 High Frequency Driver replacement: 8 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 9 9 10 10 11 11 12 12 2 2 Twelve screws and fl at washers need to be removed from the horn assembly using the phillips head screwdriver. Once the screws are removed, the horn assembly may be loosened by prying a fl at head screwdriver in between the cabinet and the horn assembl ...

  • Alvarez S408 - page 12

    12 3 3 Carefully begin to remove the entire horn assembly (with the high frequency driver still attached). Caution: The horn weighs about 8 pounds, and the weight is unevenly distributed. High Frequency Driver replacement continued: 4 4 The positive (red and black) and negative (solid black) cables are still attached to the high frequency driver te ...

  • Alvarez S408 - page 13

    13 High Frequency Driver replacement continued: 6 6 Four bolts and eight washers may be removed from the driver using the 8mm combination wrench. Turn counter- clockwise to loosen and remove, clockwise to tighten. The other three are located around the horn assembly. Notice that the fl at washer is on the bottom, followed by the locking washer, an ...

  • Alvarez S408 - page 14

    14 3 3 The horn assembly is shown above with the high frequency driver circled. Four screws need to be removed from the driver using the 3mm allen wrench. 4 4 Keep the four screws in a safe place. 5 5 The diaphragm and plate adapter are easily removed from the horn assembly. Notice the terminal locations in relation to the indents of the high frequ ...

  • Alvarez S408 - page 15

    15 7 7 This is what the plate adapter (left) and diaphragm (right) both look like. Place the new diaphragm (part # coming soon) where the old one was. Follow the same steps as above, but backwards 6 to 1. Power up the S408 and the new diaphragm should now be pumping out those highs again. Sweet, you just replaced a diaphragm! Diaphragm replacement ...

  • Alvarez S408 - page 16

    16 Input assembly replacement: 1 1 Eight screws need to be removed from the input assembly (located on the rear of the cabinet) using the phillips head screwdriver. Once the screws are removed, the input assembly may be loosened by prying a fl at head screwdriver in between it and the cabinet. Keep the eight screws in a safe place. 1 1 2 2 3 3 4 4 ...

  • Alvarez S408 - page 17

    17 3 3 Two cables need to be removed from the input assembly PCB (as shown on the left and above): (1) the solid black cable attaches to the negative terminal (connection J4). This is for the input jack, and (2) the grey and black cable attaches to the positive terminal (connection J3). This is for the thru jack. Do not force cable removal or conne ...

  • Alvarez S408 - page 18

    18 Input assembly replacement continued: 4 4 Place the new input assembly (part #0012048) where the old one was. Follow the same steps as above, but backwards 3 to 1. Remove the serial number from the faulty input assembly (as shown in the picture above) and place on the new input assembly. Power up the S408 and relish in the fact that you just rep ...

  • Alvarez S408 - page 19

    19 This page left blank intentionally ...

メーカー Alvarez カテゴリー Car Speaker

Alvarez S408のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- S408の取扱説明書
- Alvarezの製品カード
- パンフレット
- またはAlvarez S408の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Alvarez S408の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Alvarez S408の取り付け説明書、サービスマニュアル、簡易説明書、またはAlvarez S408のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Alvarez S408の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Alvarez S408デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAlvarez S408を使用するのを助ける技術的文書のことです。説明書は通常、全てのAlvarez S408ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Alvarezの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Alvarez S408の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAlvarez S408の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Alvarez S408に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Alvarez S408デバイスの基本機能を使うにあたってのヒント。 Alvarez S408のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Alvarez S408に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAlvarez S408のメーカー/サービスへの連絡先に関する情報。

Alvarez S408についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAlvarez S408の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAlvarez S408で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)