Italiano dropdown-ico

Manuale per l’uso Alvarez S408

19 pagine 1.19 mb
Scarica

Vai alla pagina of 19

Summary
  • Alvarez S408 - page 1

    1 S408 REPAIR MANUAL S408 REPAIR MANUAL ...

  • Alvarez S408 - page 2

    2 These instructions are intended to help restore any ailing S408 Passive Loudspeaker back to factory working conditions. They show how to remove and replace the drivers. Please contact Mackie Technical Support (1-800-898-3211) to receive a Service Request Number and Order Number for parts needed for this restoration. They will also help you determ ...

  • Alvarez S408 - page 3

    3 Top left woofer replacement: 1 1 Six screws need to be removed from each side of the front of the grill (twelve screws total) using the phillips head screwdriver. This grill has a tendency to want to “pop” off, so please be sure to hold it in place with one hand or arm while removing the screws with your free hand. In addition to the grill, t ...

  • Alvarez S408 - page 4

    4 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Top left woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on the te ...

  • Alvarez S408 - page 5

    5 Top right woofer replacement: 2 2 Eight screws need to be removed from the woofer using the phillips head screwdriver. Once the screws are removed, the woofer may be loosened by prying a fl at head screwdriver in between the cabinet and the woofer; a good place to start is in the notches located just above the horn assembly and below the woofer ...

  • Alvarez S408 - page 6

    6 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Top right woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on the t ...

  • Alvarez S408 - page 7

    7 Bottom left woofer replacement: 2 2 Eight screws need to be removed from the woofer using the phillips head screwdriver. Once the screws are removed, the woofer may be loosened by prying a fl at head screwdriver in between the cabinet and the woofer; a good place to start is in the notches located just below the horn assembly and above the woofe ...

  • Alvarez S408 - page 8

    8 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Bottom left woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on the ...

  • Alvarez S408 - page 9

    9 Bottom right woofer replacement: 2 2 Eight screws need to be removed from the woofer using the phillips head screwdriver. Once the screws are removed, the woofer may be loosened by prying a fl at head screwdriver in between the cabinet and the woofer; a good place to start is in the notches located just below the horn assembly and above the woof ...

  • Alvarez S408 - page 10

    10 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Bottom right woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on t ...

  • Alvarez S408 - page 11

    11 High Frequency Driver replacement: 8 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 9 9 10 10 11 11 12 12 2 2 Twelve screws and fl at washers need to be removed from the horn assembly using the phillips head screwdriver. Once the screws are removed, the horn assembly may be loosened by prying a fl at head screwdriver in between the cabinet and the horn assembl ...

  • Alvarez S408 - page 12

    12 3 3 Carefully begin to remove the entire horn assembly (with the high frequency driver still attached). Caution: The horn weighs about 8 pounds, and the weight is unevenly distributed. High Frequency Driver replacement continued: 4 4 The positive (red and black) and negative (solid black) cables are still attached to the high frequency driver te ...

  • Alvarez S408 - page 13

    13 High Frequency Driver replacement continued: 6 6 Four bolts and eight washers may be removed from the driver using the 8mm combination wrench. Turn counter- clockwise to loosen and remove, clockwise to tighten. The other three are located around the horn assembly. Notice that the fl at washer is on the bottom, followed by the locking washer, an ...

  • Alvarez S408 - page 14

    14 3 3 The horn assembly is shown above with the high frequency driver circled. Four screws need to be removed from the driver using the 3mm allen wrench. 4 4 Keep the four screws in a safe place. 5 5 The diaphragm and plate adapter are easily removed from the horn assembly. Notice the terminal locations in relation to the indents of the high frequ ...

  • Alvarez S408 - page 15

    15 7 7 This is what the plate adapter (left) and diaphragm (right) both look like. Place the new diaphragm (part # coming soon) where the old one was. Follow the same steps as above, but backwards 6 to 1. Power up the S408 and the new diaphragm should now be pumping out those highs again. Sweet, you just replaced a diaphragm! Diaphragm replacement ...

  • Alvarez S408 - page 16

    16 Input assembly replacement: 1 1 Eight screws need to be removed from the input assembly (located on the rear of the cabinet) using the phillips head screwdriver. Once the screws are removed, the input assembly may be loosened by prying a fl at head screwdriver in between it and the cabinet. Keep the eight screws in a safe place. 1 1 2 2 3 3 4 4 ...

  • Alvarez S408 - page 17

    17 3 3 Two cables need to be removed from the input assembly PCB (as shown on the left and above): (1) the solid black cable attaches to the negative terminal (connection J4). This is for the input jack, and (2) the grey and black cable attaches to the positive terminal (connection J3). This is for the thru jack. Do not force cable removal or conne ...

  • Alvarez S408 - page 18

    18 Input assembly replacement continued: 4 4 Place the new input assembly (part #0012048) where the old one was. Follow the same steps as above, but backwards 3 to 1. Remove the serial number from the faulty input assembly (as shown in the picture above) and place on the new input assembly. Power up the S408 and relish in the fact that you just rep ...

  • Alvarez S408 - page 19

    19 This page left blank intentionally ...

Fabbricante Alvarez Categoria Car Speaker

I documenti che otteniamo dal fabbricante del dispositivoAlvarez S408 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Alvarez
- manuali per l’uso S408
- schede prodotto Alvarez
- opuscoli
- o etichette energetiche Alvarez S408
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Alvarez S408.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Alvarez S408, manuali di manutenzione, brevi manuali o manuali utente Alvarez S408. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Alvarez S408.

Manuali per l’uso simili

Manuale completo del dispositivo Alvarez S408, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Alvarez S408 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Alvarez S408.

Il manuale per l’uso completo Alvarez, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Alvarez S408 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Alvarez S408, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Alvarez S408 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Alvarez S408 - che ci dovrebbe aiutare nei primi passi durante l'uso Alvarez S408
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Alvarez S408
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Alvarez S408 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Alvarez S408?

Utilizza il modulo sottostante

Se non hai risolto il problema con Alvarez S408 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Alvarez S408 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)