Русский dropdown-ico

Инструкция обслуживания Alvarez S408

19 страниц 1.19 mb
Скачать

Перейти на страницу of 19

Summary
  • Alvarez S408 - page 1

    1 S408 REPAIR MANUAL S408 REPAIR MANUAL ...

  • Alvarez S408 - page 2

    2 These instructions are intended to help restore any ailing S408 Passive Loudspeaker back to factory working conditions. They show how to remove and replace the drivers. Please contact Mackie Technical Support (1-800-898-3211) to receive a Service Request Number and Order Number for parts needed for this restoration. They will also help you determ ...

  • Alvarez S408 - page 3

    3 Top left woofer replacement: 1 1 Six screws need to be removed from each side of the front of the grill (twelve screws total) using the phillips head screwdriver. This grill has a tendency to want to “pop” off, so please be sure to hold it in place with one hand or arm while removing the screws with your free hand. In addition to the grill, t ...

  • Alvarez S408 - page 4

    4 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Top left woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on the te ...

  • Alvarez S408 - page 5

    5 Top right woofer replacement: 2 2 Eight screws need to be removed from the woofer using the phillips head screwdriver. Once the screws are removed, the woofer may be loosened by prying a fl at head screwdriver in between the cabinet and the woofer; a good place to start is in the notches located just above the horn assembly and below the woofer ...

  • Alvarez S408 - page 6

    6 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Top right woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on the t ...

  • Alvarez S408 - page 7

    7 Bottom left woofer replacement: 2 2 Eight screws need to be removed from the woofer using the phillips head screwdriver. Once the screws are removed, the woofer may be loosened by prying a fl at head screwdriver in between the cabinet and the woofer; a good place to start is in the notches located just below the horn assembly and above the woofe ...

  • Alvarez S408 - page 8

    8 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Bottom left woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on the ...

  • Alvarez S408 - page 9

    9 Bottom right woofer replacement: 2 2 Eight screws need to be removed from the woofer using the phillips head screwdriver. Once the screws are removed, the woofer may be loosened by prying a fl at head screwdriver in between the cabinet and the woofer; a good place to start is in the notches located just below the horn assembly and above the woof ...

  • Alvarez S408 - page 10

    10 3 3 Carefully begin to remove the woofer. Caution: The woofer is approximately 8 pounds with the weight unevenly distributed. Bottom right woofer replacement continued: 4 4 The positive (blue and black) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on t ...

  • Alvarez S408 - page 11

    11 High Frequency Driver replacement: 8 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 9 9 10 10 11 11 12 12 2 2 Twelve screws and fl at washers need to be removed from the horn assembly using the phillips head screwdriver. Once the screws are removed, the horn assembly may be loosened by prying a fl at head screwdriver in between the cabinet and the horn assembl ...

  • Alvarez S408 - page 12

    12 3 3 Carefully begin to remove the entire horn assembly (with the high frequency driver still attached). Caution: The horn weighs about 8 pounds, and the weight is unevenly distributed. High Frequency Driver replacement continued: 4 4 The positive (red and black) and negative (solid black) cables are still attached to the high frequency driver te ...

  • Alvarez S408 - page 13

    13 High Frequency Driver replacement continued: 6 6 Four bolts and eight washers may be removed from the driver using the 8mm combination wrench. Turn counter- clockwise to loosen and remove, clockwise to tighten. The other three are located around the horn assembly. Notice that the fl at washer is on the bottom, followed by the locking washer, an ...

  • Alvarez S408 - page 14

    14 3 3 The horn assembly is shown above with the high frequency driver circled. Four screws need to be removed from the driver using the 3mm allen wrench. 4 4 Keep the four screws in a safe place. 5 5 The diaphragm and plate adapter are easily removed from the horn assembly. Notice the terminal locations in relation to the indents of the high frequ ...

  • Alvarez S408 - page 15

    15 7 7 This is what the plate adapter (left) and diaphragm (right) both look like. Place the new diaphragm (part # coming soon) where the old one was. Follow the same steps as above, but backwards 6 to 1. Power up the S408 and the new diaphragm should now be pumping out those highs again. Sweet, you just replaced a diaphragm! Diaphragm replacement ...

  • Alvarez S408 - page 16

    16 Input assembly replacement: 1 1 Eight screws need to be removed from the input assembly (located on the rear of the cabinet) using the phillips head screwdriver. Once the screws are removed, the input assembly may be loosened by prying a fl at head screwdriver in between it and the cabinet. Keep the eight screws in a safe place. 1 1 2 2 3 3 4 4 ...

  • Alvarez S408 - page 17

    17 3 3 Two cables need to be removed from the input assembly PCB (as shown on the left and above): (1) the solid black cable attaches to the negative terminal (connection J4). This is for the input jack, and (2) the grey and black cable attaches to the positive terminal (connection J3). This is for the thru jack. Do not force cable removal or conne ...

  • Alvarez S408 - page 18

    18 Input assembly replacement continued: 4 4 Place the new input assembly (part #0012048) where the old one was. Follow the same steps as above, but backwards 3 to 1. Remove the serial number from the faulty input assembly (as shown in the picture above) and place on the new input assembly. Power up the S408 and relish in the fact that you just rep ...

  • Alvarez S408 - page 19

    19 This page left blank intentionally ...

Производитель Alvarez Категория Car Speaker

Документы, которые мы получаем от производителя устройства Alvarez S408 мы можем разделить на несколько групп. Это в частности:
- технические чертежи Alvarez
- инструкции обслуживания S408
- паспорта изделия Alvarez
- информационные брошюры
- энергетические этикетки Alvarez S408
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Alvarez S408.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Alvarez S408, инструкции обслуживания, короткие инструкции или инструкции пользователя Alvarez S408. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Alvarez S408.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Alvarez S408, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Alvarez S408 пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Alvarez S408.

Полная инструкция обслуживания Alvarez, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Alvarez S408 - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Alvarez S408, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Alvarez S408, которое найдем в данном документе
3. Советы по использованию основных функций устройства Alvarez S408 - которые должны облегчить нам первые шаги во время использования Alvarez S408
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Alvarez S408
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Alvarez S408 в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Alvarez S408?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Alvarez S408, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Alvarez S408 со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Captcha
Новая картинка

Комментарии (0)