Bedienungsanleitung Philips CM-20

11 Seiten 0.08 mb
Download

Zur Seite of 11

Summary
  • Philips CM-20 - page 1

    OPERATION PROCEDURES FOR PHILIPS/FEI CM-20 TRANSMISSION ELECTRON MICROSCOPE General Comments Normally the m icroscope will be left in the power ON (standby ready to operate) condition; i.e., all circuits will be con tinuously energized and the microscope will be under full vacuum (MAIN, VACUUM, HIGH TENSION lamps on th e right control panel are all ...

  • Philips CM-20 - page 2

    (2) Hold the specimen holder with the airlock-op ening pin up. Carefully insert the specimen holder into the airlock entry and slide it in un til stop. At this point , pre-pumping of the airlock commences as indicated by illum ina tion of the red airlock indicator light. (3) After hearing a click sound, gr ape the specimen holder and turn clockwise ...

  • Philips CM-20 - page 3

    (4) Make sure the camera cover is correctly pl aced, and then press CAM AIR again to pump the camera chamber. You should be able to hear the mechanical pum p starting. Pull on the camera lid to ensure the vacuum is pulling. (5) Press READY, then TEM CAMERA, and CAM INIT. (6) Press RESET to reset film numb er (to 36), and press READY. (7) Press MODE ...

  • Philips CM-20 - page 4

    ROUTINE ALIGNMENT PROCEDUR ES FOR PHILIPS CM-20 TEM The following protocol is not intended to be spec ific. It is intended to be used as a mean to refresh one’s memory in carry out step by st ep procedures which are necessary to obtain reasonably good results with the transmission electron microscopes. More specific information can be obtained fr ...

  • Philips CM-20 - page 5

    (6) Set voltage at 20. Push HIGH TENSI ON button (the green LED should light) Slowly increase voltage from 20 kV to 160 kV using soft keys (wait 1 minute between each step). (7) After voltage reaches 160 kV, press FR EE CONTROL soft key. Use focus knob, slowly increase voltage from 160kV to 200kV. If it arcs (loud popping sound), use focus step siz ...

  • Philips CM-20 - page 6

    by first making crossover image with INTENSITY knob, then open up condenser II (INTENSITY)/expand the beam and close condenser II on the opposite side of crossover. If the beam appears to sw ing this indicates th e aperture is not properly centered. Center the aperture by moving the X and Y controls on the aperture housing. (5) Repeat the last step ...

  • Philips CM-20 - page 7

    (4) Condenser lens astigmatism correction - Press STIG to activate stigmator control. - Press COND soft key so that it is highlighted (the default is OBJ). - Condense the beam. - Use MULTIFUNCTION knobs to correct the astigmatism. The beam should be round when changing the setting of the INTENSI TY knob, or the filament image will be sharpest if fi ...

  • Philips CM-20 - page 8

    - Press ALGN to de-activate. (3) Voltage centering - Place a more or less symmetrical im age to the center. - Condense the beam at the center of screen, and spread the beam . - Press ROT CENTER and VOLT soft keys in ALGN. - Make sure it is in the VOLT m ode (check bottom right soft key). - Determine the voltage center from the m ovement of the enti ...

  • Philips CM-20 - page 9

    (5) Change camera length (by changi ng MAGNIFICATION knob) to 44.0 mm. (6) Realign the diffraction pattern. (7) Repeat steps 4 to 6 until the transm itted spot remains at (near) the center w hile changing camera length between 44.0 mm to 3.2 m . (8) Deactivate ALGN, and depress D to get out of diffraction mode. (iv) Insertion and centering objectiv ...

  • Philips CM-20 - page 10

    (2) Set a magnification at least 3 or 4 times hi gher than that will used for photographing. (3) Obtain the thinnest over-focus (Fresnel) fringe that can be clearly seen in the binocular, with beam spread. Caution: make sure you focus the binocular on the viewing screen. (4) Adjust the OJB STIG X and Y (MULTIFUNCTION keys) until the fringe fo llows ...

  • Philips CM-20 - page 11

    WAC 09/28/02 VI. COMPUTER ALIGNMENT AND AS TGMATISM CORRECTION FOR 200 kV 1. Preses PARAMETERS on TEM br ight field page 3 times 2. Press REMOTE CONTROL to highlight it (This w ill allow the com puter to talk to the TEM). 3. Turn on the PC monitor (on/o ff switch on back of m onitor). 4. If computer is already in execution mode, go to step 6 5. At ...

Produzent Philips Kategorie Microscope & Magnifier

Dokumente, die wir vom Produzenten des Geräts Philips CM-20 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Philips
- Bedienungsanleitungen CM-20
- Produktkarten Philips
- Informationsbroschüren
- oder Energieetiketten Philips CM-20
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Philips CM-20.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Philips CM-20, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Philips CM-20. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Philips CM-20 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Philips CM-20, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Philips CM-20 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Philips CM-20 verständlich ist.

Eine gänzliche Bedienungsanleitung von Philips sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Philips CM-20 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Philips CM-20 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Philips CM-20, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Philips CM-20 - die uns die ersten Schritte während der Nutzung von Philips CM-20 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Philips CM-20 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Philips CM-20 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Philips CM-20?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Philips CM-20 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Philips CM-20 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)