Manuel d’utilisation Philips CM-20

11 pages 0.08 mb
Télécharger

Aller à la page of 11

Summary
  • Philips CM-20 - page 1

    OPERATION PROCEDURES FOR PHILIPS/FEI CM-20 TRANSMISSION ELECTRON MICROSCOPE General Comments Normally the m icroscope will be left in the power ON (standby ready to operate) condition; i.e., all circuits will be con tinuously energized and the microscope will be under full vacuum (MAIN, VACUUM, HIGH TENSION lamps on th e right control panel are all ...

  • Philips CM-20 - page 2

    (2) Hold the specimen holder with the airlock-op ening pin up. Carefully insert the specimen holder into the airlock entry and slide it in un til stop. At this point , pre-pumping of the airlock commences as indicated by illum ina tion of the red airlock indicator light. (3) After hearing a click sound, gr ape the specimen holder and turn clockwise ...

  • Philips CM-20 - page 3

    (4) Make sure the camera cover is correctly pl aced, and then press CAM AIR again to pump the camera chamber. You should be able to hear the mechanical pum p starting. Pull on the camera lid to ensure the vacuum is pulling. (5) Press READY, then TEM CAMERA, and CAM INIT. (6) Press RESET to reset film numb er (to 36), and press READY. (7) Press MODE ...

  • Philips CM-20 - page 4

    ROUTINE ALIGNMENT PROCEDUR ES FOR PHILIPS CM-20 TEM The following protocol is not intended to be spec ific. It is intended to be used as a mean to refresh one’s memory in carry out step by st ep procedures which are necessary to obtain reasonably good results with the transmission electron microscopes. More specific information can be obtained fr ...

  • Philips CM-20 - page 5

    (6) Set voltage at 20. Push HIGH TENSI ON button (the green LED should light) Slowly increase voltage from 20 kV to 160 kV using soft keys (wait 1 minute between each step). (7) After voltage reaches 160 kV, press FR EE CONTROL soft key. Use focus knob, slowly increase voltage from 160kV to 200kV. If it arcs (loud popping sound), use focus step siz ...

  • Philips CM-20 - page 6

    by first making crossover image with INTENSITY knob, then open up condenser II (INTENSITY)/expand the beam and close condenser II on the opposite side of crossover. If the beam appears to sw ing this indicates th e aperture is not properly centered. Center the aperture by moving the X and Y controls on the aperture housing. (5) Repeat the last step ...

  • Philips CM-20 - page 7

    (4) Condenser lens astigmatism correction - Press STIG to activate stigmator control. - Press COND soft key so that it is highlighted (the default is OBJ). - Condense the beam. - Use MULTIFUNCTION knobs to correct the astigmatism. The beam should be round when changing the setting of the INTENSI TY knob, or the filament image will be sharpest if fi ...

  • Philips CM-20 - page 8

    - Press ALGN to de-activate. (3) Voltage centering - Place a more or less symmetrical im age to the center. - Condense the beam at the center of screen, and spread the beam . - Press ROT CENTER and VOLT soft keys in ALGN. - Make sure it is in the VOLT m ode (check bottom right soft key). - Determine the voltage center from the m ovement of the enti ...

  • Philips CM-20 - page 9

    (5) Change camera length (by changi ng MAGNIFICATION knob) to 44.0 mm. (6) Realign the diffraction pattern. (7) Repeat steps 4 to 6 until the transm itted spot remains at (near) the center w hile changing camera length between 44.0 mm to 3.2 m . (8) Deactivate ALGN, and depress D to get out of diffraction mode. (iv) Insertion and centering objectiv ...

  • Philips CM-20 - page 10

    (2) Set a magnification at least 3 or 4 times hi gher than that will used for photographing. (3) Obtain the thinnest over-focus (Fresnel) fringe that can be clearly seen in the binocular, with beam spread. Caution: make sure you focus the binocular on the viewing screen. (4) Adjust the OJB STIG X and Y (MULTIFUNCTION keys) until the fringe fo llows ...

  • Philips CM-20 - page 11

    WAC 09/28/02 VI. COMPUTER ALIGNMENT AND AS TGMATISM CORRECTION FOR 200 kV 1. Preses PARAMETERS on TEM br ight field page 3 times 2. Press REMOTE CONTROL to highlight it (This w ill allow the com puter to talk to the TEM). 3. Turn on the PC monitor (on/o ff switch on back of m onitor). 4. If computer is already in execution mode, go to step 6 5. At ...

Fabricant Philips Catégorie Microscope & Magnifier

Les documents que nous recevons du fabricant de l'appareilPhilips CM-20 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Philips
- manuels d’utilisations CM-20
- fiches produit Philips
- dépliants
- ou étiquettes-énergie Philips CM-20
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Philips CM-20.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Philips CM-20, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Philips CM-20. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Philips CM-20.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Philips CM-20, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Philips CM-20 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Philips CM-20.

Le manuel d’utilisation complet Philips, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Philips CM-20 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Philips CM-20, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lPhilips CM-20 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Philips CM-20 - qui devraient nous aider dans les premières étapes lors de l'utilisation Philips CM-20
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Philips CM-20
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Philips CM-20 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Philips CM-20?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Philips CM-20, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Philips CM-20 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)