Manuale per l’uso Philips CM-20

11 pagine 0.08 mb
Scarica

Vai alla pagina of 11

Summary
  • Philips CM-20 - page 1

    OPERATION PROCEDURES FOR PHILIPS/FEI CM-20 TRANSMISSION ELECTRON MICROSCOPE General Comments Normally the m icroscope will be left in the power ON (standby ready to operate) condition; i.e., all circuits will be con tinuously energized and the microscope will be under full vacuum (MAIN, VACUUM, HIGH TENSION lamps on th e right control panel are all ...

  • Philips CM-20 - page 2

    (2) Hold the specimen holder with the airlock-op ening pin up. Carefully insert the specimen holder into the airlock entry and slide it in un til stop. At this point , pre-pumping of the airlock commences as indicated by illum ina tion of the red airlock indicator light. (3) After hearing a click sound, gr ape the specimen holder and turn clockwise ...

  • Philips CM-20 - page 3

    (4) Make sure the camera cover is correctly pl aced, and then press CAM AIR again to pump the camera chamber. You should be able to hear the mechanical pum p starting. Pull on the camera lid to ensure the vacuum is pulling. (5) Press READY, then TEM CAMERA, and CAM INIT. (6) Press RESET to reset film numb er (to 36), and press READY. (7) Press MODE ...

  • Philips CM-20 - page 4

    ROUTINE ALIGNMENT PROCEDUR ES FOR PHILIPS CM-20 TEM The following protocol is not intended to be spec ific. It is intended to be used as a mean to refresh one’s memory in carry out step by st ep procedures which are necessary to obtain reasonably good results with the transmission electron microscopes. More specific information can be obtained fr ...

  • Philips CM-20 - page 5

    (6) Set voltage at 20. Push HIGH TENSI ON button (the green LED should light) Slowly increase voltage from 20 kV to 160 kV using soft keys (wait 1 minute between each step). (7) After voltage reaches 160 kV, press FR EE CONTROL soft key. Use focus knob, slowly increase voltage from 160kV to 200kV. If it arcs (loud popping sound), use focus step siz ...

  • Philips CM-20 - page 6

    by first making crossover image with INTENSITY knob, then open up condenser II (INTENSITY)/expand the beam and close condenser II on the opposite side of crossover. If the beam appears to sw ing this indicates th e aperture is not properly centered. Center the aperture by moving the X and Y controls on the aperture housing. (5) Repeat the last step ...

  • Philips CM-20 - page 7

    (4) Condenser lens astigmatism correction - Press STIG to activate stigmator control. - Press COND soft key so that it is highlighted (the default is OBJ). - Condense the beam. - Use MULTIFUNCTION knobs to correct the astigmatism. The beam should be round when changing the setting of the INTENSI TY knob, or the filament image will be sharpest if fi ...

  • Philips CM-20 - page 8

    - Press ALGN to de-activate. (3) Voltage centering - Place a more or less symmetrical im age to the center. - Condense the beam at the center of screen, and spread the beam . - Press ROT CENTER and VOLT soft keys in ALGN. - Make sure it is in the VOLT m ode (check bottom right soft key). - Determine the voltage center from the m ovement of the enti ...

  • Philips CM-20 - page 9

    (5) Change camera length (by changi ng MAGNIFICATION knob) to 44.0 mm. (6) Realign the diffraction pattern. (7) Repeat steps 4 to 6 until the transm itted spot remains at (near) the center w hile changing camera length between 44.0 mm to 3.2 m . (8) Deactivate ALGN, and depress D to get out of diffraction mode. (iv) Insertion and centering objectiv ...

  • Philips CM-20 - page 10

    (2) Set a magnification at least 3 or 4 times hi gher than that will used for photographing. (3) Obtain the thinnest over-focus (Fresnel) fringe that can be clearly seen in the binocular, with beam spread. Caution: make sure you focus the binocular on the viewing screen. (4) Adjust the OJB STIG X and Y (MULTIFUNCTION keys) until the fringe fo llows ...

  • Philips CM-20 - page 11

    WAC 09/28/02 VI. COMPUTER ALIGNMENT AND AS TGMATISM CORRECTION FOR 200 kV 1. Preses PARAMETERS on TEM br ight field page 3 times 2. Press REMOTE CONTROL to highlight it (This w ill allow the com puter to talk to the TEM). 3. Turn on the PC monitor (on/o ff switch on back of m onitor). 4. If computer is already in execution mode, go to step 6 5. At ...

Fabbricante Philips Categoria Microscope & Magnifier

I documenti che otteniamo dal fabbricante del dispositivoPhilips CM-20 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Philips
- manuali per l’uso CM-20
- schede prodotto Philips
- opuscoli
- o etichette energetiche Philips CM-20
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Philips CM-20.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Philips CM-20, manuali di manutenzione, brevi manuali o manuali utente Philips CM-20. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Philips CM-20.

Manuali per l’uso simili

Manuale completo del dispositivo Philips CM-20, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Philips CM-20 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Philips CM-20.

Il manuale per l’uso completo Philips, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Philips CM-20 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Philips CM-20, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Philips CM-20 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Philips CM-20 - che ci dovrebbe aiutare nei primi passi durante l'uso Philips CM-20
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Philips CM-20
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Philips CM-20 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Philips CM-20?

Utilizza il modulo sottostante

Se non hai risolto il problema con Philips CM-20 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Philips CM-20 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)