Bedienungsanleitung Actron 9040

12 Seiten 0.64 mb
Download

Zur Seite of 12

Summary
  • Actron 9040 - page 1

    Retrieves Global (Generic) OBD II diagnostic codes and displays their definitions on Foreign and Domestic OBD II compliant vehicles 9040 Global OBD II Code Scanner ® Content s Safety Precautions ................................................................................... 2 About OBD II ....................................................... ...

  • Actron 9040 - page 2

    2 OBD II stands for On-Board Diagnostics version II. OBD II is a system that the Society of Automotive Engineers (SAE) developed to standardize automotive electronic diagnosis to minimize vehicle pollution and to allow you to use the same tool to test any make and model without special adapters. The SAE established guidelines that provide:  a un ...

  • Actron 9040 - page 3

    3 Diagnostic T r ouble Code(s) (DTC) Diagnostic Trouble Codes (DTCs) consist of a five-digit alphanumeric code in the for- mat shown below . When the On-Board Computer recognizes and identifies a problem in the computer-monitored systems, a DTC for that fault is stored in memory . These codes are intended to help you determine the root cause of a p ...

  • Actron 9040 - page 4

    4 Control and Indicators The scan tool is designed to be as intuitive as possible. All menu and lists operate the same way .  ENTER Key - selects displayed items and moves cursor in the Code Lookup function.  YES/UP Arrow Key - responds yes to prompts, scrolls up and changes numbers in Code Lookup.  NO/DOWN Arrow Key - responds no to promp ...

  • Actron 9040 - page 5

    5 Using the Code Scanner ® Turn the ignition key to the KOEO or KOER. Select Read Codes and press ENTER . If there are no codes stored in vehicle memory , a System Pass message displays. If codes have been stored in vehicle memory , then the num- ber of codes and type display (i.e. = 1 of 3 ; ). Press the DOWN arrow to view the codes. The de ...

  • Actron 9040 - page 6

    6 Using the Code Scanner ® Select I/M Monitors and press the ENTER key . Each I/M monitor and its status display per screen. Use the arrow keys to view them. When done, press the BACK key .  A status of Ready means that the required driving conditions for that monitor have been meet and it passed.  A status of Not Ready means tha ...

  • Actron 9040 - page 7

    7  Inspect all vacuum hoses for: * Correct routing. Refer to vehicle service manual, or V ehicle Emission Control Information (VECI) decal located in the engine compartment. * Pinches and kinks. * S plits, cut s or breaks  Inspect wiring for: * Contact with sharp edges (a common problem). * Contact with hot surfaces, such as exhaust  Inspe ...

  • Actron 9040 - page 8

    8 V ehicle Service Information V ehicle service manuals containing additional diagnostic information are available at most auto parts stores or the local library . If unable to locate them at those locations, write the below listed publishers for availability and pricing. Please be sure to specify the make, model and year of vehicle. Chilton Book C ...

  • Actron 9040 - page 9

    9 Gl obal P arameter li st All parameter identification data (PID) listed was verified on actual vehicles to guaran- tee accuracy . Definitions used to describe all PIDs were obtained from reliable sources and are accurate at time of printing. It is possible that some newer vehicles may contain data different from that listed in Appendix A. Always ...

  • Actron 9040 - page 10

    10 CALC LOAD (0 - 100%) Calulated LOAD Value indicates load on engine. C A T TEMPxy (-40°C - 6513.5°C) or (-40 - 9999.9F) Cataly st T emperature Bank shall display catalyst substrate temperature for bank catalyst, if used by control module strategy for on board diagnostics monitoring, bank, sensor catalyst or tempera- ture sensor. CLR DST (0km-65 ...

  • Actron 9040 - page 11

    11 4. OPEN2: The PCM is operating in Open Loop control strategy due to detected system fault. Certain actuator or sensor faults will cause module to use an open loop strategy . 5. CLSD1: Closed Loop control is current storage being used by module, but a fault with at least one O2 sensor has been detected. The control system may be using single O2 f ...

  • Actron 9040 - page 12

    ©2004 SPX Actron. All Rights Reserved. Printed in USA 0002-002-2356 REL TPS (0 - 100%) Relative Throttle Position is relative throttle position at normal position. SECOND AI R (AI R_ST AT : UPS, DNS or OFF) Commanded Secondary Air St atus is on newer vehicles and actuators to control pollution control. UPS - UP STREAM module is demanding that seco ...

Produzent Actron Kategorie Scanner

Dokumente, die wir vom Produzenten des Geräts Actron 9040 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Actron
- Bedienungsanleitungen 9040
- Produktkarten Actron
- Informationsbroschüren
- oder Energieetiketten Actron 9040
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Actron 9040.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Actron 9040, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Actron 9040. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Actron 9040 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Actron 9040, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Actron 9040 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Actron 9040 verständlich ist.

Eine gänzliche Bedienungsanleitung von Actron sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Actron 9040 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Actron 9040 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Actron 9040, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Actron 9040 - die uns die ersten Schritte während der Nutzung von Actron 9040 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Actron 9040 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Actron 9040 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Actron 9040?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Actron 9040 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Actron 9040 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)