Actron 9040の取扱説明書

12ページ 0.64 mb
ダウンロード

ページに移動 of 12

Summary
  • Actron 9040 - page 1

    Retrieves Global (Generic) OBD II diagnostic codes and displays their definitions on Foreign and Domestic OBD II compliant vehicles 9040 Global OBD II Code Scanner ® Content s Safety Precautions ................................................................................... 2 About OBD II ....................................................... ...

  • Actron 9040 - page 2

    2 OBD II stands for On-Board Diagnostics version II. OBD II is a system that the Society of Automotive Engineers (SAE) developed to standardize automotive electronic diagnosis to minimize vehicle pollution and to allow you to use the same tool to test any make and model without special adapters. The SAE established guidelines that provide:  a un ...

  • Actron 9040 - page 3

    3 Diagnostic T r ouble Code(s) (DTC) Diagnostic Trouble Codes (DTCs) consist of a five-digit alphanumeric code in the for- mat shown below . When the On-Board Computer recognizes and identifies a problem in the computer-monitored systems, a DTC for that fault is stored in memory . These codes are intended to help you determine the root cause of a p ...

  • Actron 9040 - page 4

    4 Control and Indicators The scan tool is designed to be as intuitive as possible. All menu and lists operate the same way .  ENTER Key - selects displayed items and moves cursor in the Code Lookup function.  YES/UP Arrow Key - responds yes to prompts, scrolls up and changes numbers in Code Lookup.  NO/DOWN Arrow Key - responds no to promp ...

  • Actron 9040 - page 5

    5 Using the Code Scanner ® Turn the ignition key to the KOEO or KOER. Select Read Codes and press ENTER . If there are no codes stored in vehicle memory , a System Pass message displays. If codes have been stored in vehicle memory , then the num- ber of codes and type display (i.e. = 1 of 3 ; ). Press the DOWN arrow to view the codes. The de ...

  • Actron 9040 - page 6

    6 Using the Code Scanner ® Select I/M Monitors and press the ENTER key . Each I/M monitor and its status display per screen. Use the arrow keys to view them. When done, press the BACK key .  A status of Ready means that the required driving conditions for that monitor have been meet and it passed.  A status of Not Ready means tha ...

  • Actron 9040 - page 7

    7  Inspect all vacuum hoses for: * Correct routing. Refer to vehicle service manual, or V ehicle Emission Control Information (VECI) decal located in the engine compartment. * Pinches and kinks. * S plits, cut s or breaks  Inspect wiring for: * Contact with sharp edges (a common problem). * Contact with hot surfaces, such as exhaust  Inspe ...

  • Actron 9040 - page 8

    8 V ehicle Service Information V ehicle service manuals containing additional diagnostic information are available at most auto parts stores or the local library . If unable to locate them at those locations, write the below listed publishers for availability and pricing. Please be sure to specify the make, model and year of vehicle. Chilton Book C ...

  • Actron 9040 - page 9

    9 Gl obal P arameter li st All parameter identification data (PID) listed was verified on actual vehicles to guaran- tee accuracy . Definitions used to describe all PIDs were obtained from reliable sources and are accurate at time of printing. It is possible that some newer vehicles may contain data different from that listed in Appendix A. Always ...

  • Actron 9040 - page 10

    10 CALC LOAD (0 - 100%) Calulated LOAD Value indicates load on engine. C A T TEMPxy (-40°C - 6513.5°C) or (-40 - 9999.9F) Cataly st T emperature Bank shall display catalyst substrate temperature for bank catalyst, if used by control module strategy for on board diagnostics monitoring, bank, sensor catalyst or tempera- ture sensor. CLR DST (0km-65 ...

  • Actron 9040 - page 11

    11 4. OPEN2: The PCM is operating in Open Loop control strategy due to detected system fault. Certain actuator or sensor faults will cause module to use an open loop strategy . 5. CLSD1: Closed Loop control is current storage being used by module, but a fault with at least one O2 sensor has been detected. The control system may be using single O2 f ...

  • Actron 9040 - page 12

    ©2004 SPX Actron. All Rights Reserved. Printed in USA 0002-002-2356 REL TPS (0 - 100%) Relative Throttle Position is relative throttle position at normal position. SECOND AI R (AI R_ST AT : UPS, DNS or OFF) Commanded Secondary Air St atus is on newer vehicles and actuators to control pollution control. UPS - UP STREAM module is demanding that seco ...

メーカー Actron カテゴリー Scanner

Actron 9040のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 9040の取扱説明書
- Actronの製品カード
- パンフレット
- またはActron 9040の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Actron 9040の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Actron 9040の取り付け説明書、サービスマニュアル、簡易説明書、またはActron 9040のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Actron 9040の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Actron 9040デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがActron 9040を使用するのを助ける技術的文書のことです。説明書は通常、全てのActron 9040ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Actronの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Actron 9040の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははActron 9040の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Actron 9040に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Actron 9040デバイスの基本機能を使うにあたってのヒント。 Actron 9040のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Actron 9040に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるActron 9040のメーカー/サービスへの連絡先に関する情報。

Actron 9040についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもActron 9040の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがActron 9040で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)