Aquacal HP7の取扱説明書

29ページ 0.52 mb
ダウンロード

ページに移動 of 29

Summary
  • Aquacal HP7 - page 1

    Operating & Service Instructions -for- HP7 Microprocessor Controller Includes Co nnecti on of External Controllers Dealer & Service Version Not for Distribution to Owners 2737 24 th Street North St. Petersburg, FL 33713 800-786-7751 www.aquacal.com ...

  • Aquacal HP7 - page 2

    Revised 10/14/03 TABLE of CONTENTS GENERAL DESCRIPTION of HP7 CONTROLLER ................................................. 4 HP7 CONTROLLER SPECIFICATIONS .................................................................... 4 Inputs: .................................................................................................................... ...

  • Aquacal HP7 - page 3

    2. Time Delay [dEL] : ......................................................................................................................12 3. Configuring for External C ontrollers [JAO] or [FS2]: ................................................................12 4. Water Sensor calibration [tSC]… .............................................. ...

  • Aquacal HP7 - page 4

    GENERAL DESCRIPTION of HP7 CONTROLLER The HP7 is a powerful microprocessor control designed for use in swimming pool & spa heat pumps. The control features 3-digit temperatur e and set point display, with programming changes easily performed via simple 3-button (key) operation. The HP7 offers precise water temperature contro l, accu rate defros ...

  • Aquacal HP7 - page 5

    Control Features: ♦ Compressor Operation ♦ Refrigerant Circuit Hi & Low-Pressure Lock Out ♦ Water Pump Option (Call Flex) ♦ Precise Evaporator Tem perature Control (Defrost Management) ♦ Anti Short Cycle Timer (4-Minute Restart Delay) ♦ Precise Water Temperature Control ♦ Corrosion Protection (Conformal Coating) CONTROL PANEL LAYO ...

  • Aquacal HP7 - page 6

    CONTROL PANEL SYMBOLS UNIT is HEATING WATER TEMPERATURE SET POINT ACTUAL WATER TEMPERATURE POOL SELECTION SPA SELECTION 6 ...

  • Aquacal HP7 - page 7

    SEQUENCE of OPERATION PUMP O F F POWER ON ______________________ "F LO " D isp la yed PUMP O N POWER ON ______________________ Wa t e r T e m p . D is p l a y e d SET PO IN T BEL O W 60 ºF ______________________ Heater i s "OFF " Pressi n g Up-Down Ke ys W ill Displa y "O FF" , Wa t er T em p . D i s p l ay e d SET PO ...

  • Aquacal HP7 - page 8

    8 START UP & SETTING OPERATING CONTROLS LEVEL-1 (Owner) ACCESS NOTE : Covered within this section are features and settings typically accessed first by the installer, and then remaining accessible by the end user (o wner ). Thes e features reside at the Level-1 ac cess point within the microprocessor . (Please see page-11 for information concer ...

  • Aquacal HP7 - page 9

    9 5. Changing The Pool Temperature Set Point: A. Using the Pool / Spa key, select the POOL tem perature set point. The pool set po int indicator light will confirm your selection by ligh ting. B. The pool temperature set point range is adjustable from 60 ° F. to 95 ° F (104 ° F in latest models) . using the Up ⇑ or Down ⇓ arrow keys. The des ...

  • Aquacal HP7 - page 10

    10 5) With [ELC] displayed, use the Up or Down a rrow keys to select a lock code number. The factory set lock code is “ 17”. Not depressing any buttons for 15- seconds will allow the control to save th e selection and return to the normal operating mode. Pressing the Pool / Spa key w ill also save the se lection and step to the next menu parame ...

  • Aquacal HP7 - page 11

    11 10. Fan Speed Control… This option is not applicable to any current m odels. If option present, factory default setting of “80” MUST remain. Controllers Ve rsion .06 or newer will not contain a FAN option. LEVEL-1 DISPLAY CODES Menu Codes Description Function [FLO] No water flow detected Displayed Code Message: Appears whenever the circula ...

  • Aquacal HP7 - page 12

    WARNING !!!! Dealer & Se rvice Center Use Only SERVICE & SET UP FEATURES LEVEL-2 ACCESS (Includes Configur ation for External Cont rollers) 1. Entering Service Menu: A. To enter the service menu leve l, depress and hold both the Up ⇑ and Down ⇓ arrow keys simultaneously until the code message [CF1] (Celsius Fahrenheit Selection) is disp ...

  • Aquacal HP7 - page 13

    WARNING !!!! Dealer & Se rvice Center Use Only 3.2: Configuring for External Controllers not Equipped with an “OFF” Position Switch, and All Double-Function Air Sw itch Controllers. (Also see Appendix Item “B”) 3.3 Remote Flow Sw itch / Automa tic Thermostat Switching [FS2]: (Also see Appendix Item “C”) A. Follow the steps 1a. throu ...

  • Aquacal HP7 - page 14

    WARNING !!!! Dealer & Se rvice Center Use Only B. Remove the unit front panel to gain a ccess to the defrost sensor . The defrost senso r will be found strapped to the suction line in comb ination with the TXV sensing bulb, or, in some models, the defrost sensor will be conn ected to the su ction lin e independent of the TXV bulb; C. Carefully ...

  • Aquacal HP7 - page 15

    WARNING !!!! Dealer & Se rvice Center Use Only 7. Changing Service Lock Code & “Backdoor” Entry… A. Changing the Code… The factory default Service Lock Code is “50”. Service personne l are strongly advised to retain the factory defau lt setting. However, should una uthorized access to the Level-2 (Service) menu be suspected, it ...

  • Aquacal HP7 - page 16

    WARNING !!!! Dealer & Se rvice Center Use Only 8) [DEL] will display (At this point you have entere d the service menu, and service- level programming will be possible.); 9) Push Pool/Spa pad until [LOC] appears on readout for the second time; 10) Push the up arrow,…The current, correct lock code will d isplay. Using the up or down arrow, the ...

  • Aquacal HP7 - page 17

    WARNING !!!! Dealer & Se rvice Center Use Only LEVEL-2 FAULT CODES Message Error Description Possible Cause [dPO] Defrost Sensor Open Cut or loose sensor wiring [PO] Water Temperature Sensor Open Cut or loose sensor wiring [dPC] Defrost sensor shorted Short circuit in defrost sensor wiring or defective sensor. [PC] Water temperatu re sensor sho ...

  • Aquacal HP7 - page 18

    WARNING !!!! Dealer & Se rvice Center Use Only APPENDIX Connecting to, and Confi guring Microprocessor for, Ext ernal Control : • A: Jandy and Pentair/Compool Brand Exte rnal Controllers Equipped with an “OFF” Position • B: External Controllers NOT Equipped with OFF Setting • C: Remote Flow Switch Connection • D: Call/Flex Option 18 ...

  • Aquacal HP7 - page 19

    Connecting Specific Jandy Or Pentair/Compool Controllers (See application table w ithin) Appendix- A Instructions For Connecting Specific Jandy Or Pentair/Compool Controllers To AquaCal’s HP7 Microprocessor 19 The microprocessor terminal block, labeled X , Y , Z, is located on the low-voltage portion of the MICROPROCESSOR POWER BOARD. (See figure ...

  • Aquacal HP7 - page 20

    Warning ! WARNING !!!! Dealer & Se rvice Center Use Only MAKE CERTAIN POWER SUPPLY TO HEATPUMP and CONT ROLLER IS DISCONNECTED PRIOR TO CONTINIUING. FAILURE TO DISCONNECT ELECTRICAL POWER MAY RESULT IN SERIOUS INJURY OR DEATH. 1. String 18/2 cable from the controller to the heat pump. 2. Locate the MICROPROCESSOR POWER BOARD inside the heat pum ...

  • Aquacal HP7 - page 21

    WARNING !!!! Dealer & Se rvice Center Use Only Warning ! MAKE CERTAIN POWER SUPPLY TO HEATPUMP and CONTROLLER IS DISCONNECTED PRIOR TO CONTINIUING. FAILURE TO DISCONNE CT ELECTRICAL POWER MAY RESULT IN SERIOUS INJURY OR DEATH. 1. String 18/3 cable from the controller to the heat pump. 2. Locate the MICROPROCESSOR POWER BOARD inside the heat pum ...

  • Aquacal HP7 - page 22

    Connecting Controllers Not Equipped With an OFF Setting (See application table within) WARNING !!!! Dealer & Se rvice Center Use Only Appendix- B HP-7 …. Interfacing External Controllers Not Equipped with an OFF Setting (Including, but not limited to, Double-Function Air Switches) Compatible Applications All Intermatic ”Air Force” Series ...

  • Aquacal HP7 - page 23

    Connecting a Remote Flow Switch WARNING !!!! Dealer & Se rvice Center Use Only Appendix- C Installing A Remote Flow Switch For Automatic Thermostat Switching A Remote Flow Switch kit is designed to allow autom atic selection of th e thermostats on AquaCal heaters equipped with HP7 Microprocessors with LED display. The Micr oprocesso r will rece ...

  • Aquacal HP7 - page 24

    FIGURE 1 FLOW SWITCH INSTALLED IN P OOL RETURN LINE WARNING !!!! Dealer & Se rvice Center Use Only SPA Return Line Installation 1. Disconnect power to the AquaCal Heater. 2. Remove front access panel and the electri c box cover (if equi pped) on the heater. 3. String the flow switches cable through an acces s hole in the side of the heater and ...

  • Aquacal HP7 - page 25

    FLOW SWITCH INSTALLED IN SPA RETURN LINE FIGURE 2 WARNING !!!! Dealer & Se rvice Center Use Only For Assistance Call AquaCal @ 800-786-7 751 Mon. – Fri. 8:00 AM – 5:00 PM 25 ...

  • Aquacal HP7 - page 26

    WARNING !!!! Dealer & Se rvice Center Use Only Installing a Call Flex Kit Appendix- D Installing a Call Flex Kit for Time Clock Management - Heaters Eq uipped With HP7 Microprocessor The CALL-FLEX is installed to manage the time clock to the desired heating style of the pool heat pump owner. With CALL-FLEX , owners select one of three heat mode ...

  • Aquacal HP7 - page 27

    WARNING !!!! Dealer & Se rvice Center Use Only Diagrams 27 ...

  • Aquacal HP7 - page 28

    CAUTION ! ONLY NON-ENERGIZING (“DRY” ) CIRCUIT SHOULD BE CONNECTED; NEVER APPLY EXTERNAL-SOURCE VOLTAGE TO THE HP7 MICROPROCE SSOR TERMINAL BOARD. FAILURE TO FOLLOW THESE INSTRUCTIONS WILL RESULT IN EQUIPMENT DAMAGE. WARNING ! DISCONNECT ALL ELECTRIC AL POWER WHI LE PERFORMIN G THIS WORK. FAIL URE TO FOLLOW THIS WARNING MAY RESU L T IN SERIOUS ...

  • Aquacal HP7 - page 29

    2737 24 th Street North St. Petersburg, FL 33713 800-786-7751 www.aquacal.com 29 ...

メーカー Aquacal カテゴリー Swimming Pool Heater

Aquacal HP7のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HP7の取扱説明書
- Aquacalの製品カード
- パンフレット
- またはAquacal HP7の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Aquacal HP7の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Aquacal HP7の取り付け説明書、サービスマニュアル、簡易説明書、またはAquacal HP7のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Aquacal HP7の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Aquacal HP7デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAquacal HP7を使用するのを助ける技術的文書のことです。説明書は通常、全てのAquacal HP7ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Aquacalの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Aquacal HP7の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAquacal HP7の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Aquacal HP7に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Aquacal HP7デバイスの基本機能を使うにあたってのヒント。 Aquacal HP7のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Aquacal HP7に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAquacal HP7のメーカー/サービスへの連絡先に関する情報。

Aquacal HP7についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAquacal HP7の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAquacal HP7で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)