English dropdown-ico

Manual Texas Instruments XIO3130 EVM

17 pages 1.22 mb
Download

Go to site of 17

Summary
  • Texas Instruments XIO3130 EVM - page 1

    1.1 Overview SLLU108 – July 2008 XIO3130 EVM The Texas Instruments XIO3130 EVM is a functional implementation of a four-port PCIe-to-PCIe switch. The XIO3130 EVM was designed to allow validation of three separate functional modes. In normal mode, the EVM is configured as a generic PCI Express (PCIe) switch. In hot-plug mode, downstream ports 1 an ...

  • Texas Instruments XIO3130 EVM - page 2

    1.2 Normal-Mode Operation Normal-Mode Operation www.ti.com By default, the EVM should be configured to operate in normal mode. The six jumpers (J7, J11, J13, J14, J15, and J16) should be covering both pins of each header (see Figure 1-2 ). Figure 1-2. Power Jumpers The dipswitch should be configured with SCL slide switch in the up position and DN1_ ...

  • Texas Instruments XIO3130 EVM - page 3

    1.3 Hot-Plug-Mode Operation www.ti.com Hot-Plug-Mode Operation Figure 1-4. GPIO Control Register • General control register (PCI register offset: D4h in each downstream bridge) – RCVR_PRSNT_EN = 0b – PRSNT pin is used to determine whether slot is present – REFCK_DIS = 0b – REFCK enabled – LINK_ACT_RPT_CAP = 1b – Slot is link active re ...

  • Texas Instruments XIO3130 EVM - page 4

    Hot-Plug-Mode Operation www.ti.com Figure 1-6. Dipswitch Configuration The EEPROM (U3) should be reconfigured for hot-plug-mode operation. See Section 1.5 for an explanation of how to configure the EEPROM. Upon deassertion of PERST, the XIO3130 automatically reads data from the EEPROM. This data is used to preset various PCI configuration register ...

  • Texas Instruments XIO3130 EVM - page 5

    1.4 ExpressCard-Mode operation www.ti.com ExpressCard-Mode operation • General control register (PCI register offset: D4h in port 1 and port 2 downstream bridges) – RCVR_PRSNT_EN = 0b – PRSNT pin is used to determine whether slot is present – REFCK_DIS = 0b – REFCK enabled – LINK_ACT_RPT_CAP = 1b – Slot is link active reporting capabl ...

  • Texas Instruments XIO3130 EVM - page 6

    ExpressCard-Mode operation www.ti.com Figure 1-8. ExpressCard Adapter Board To configure the XIO3130 EVM for ExpressCard-mode operation, connect the ribbon cable connector from J1 on the adapter board to one of the matching connectors (J2, J3 or J4) on the XIO3130 EVM board. Then plug the adapter board into the adjacent PCIe slot as shown in Figure ...

  • Texas Instruments XIO3130 EVM - page 7

    www.ti.com ExpressCard-Mode operation Figure 1-9. EVM Configuration for ExpressCard Mode To configure the XIO3130 EVM for ExpressCard-mode operation, the six jumpers (J7, J11, J13, J14, J15, J16) must be populated (see Figure 1-5 ). This routes power directly to slots 1 and 2 bypassing the TPS2363, which is not required for ExpressCard operation. T ...

  • Texas Instruments XIO3130 EVM - page 8

    1.5 Using WinROM to Configure the EEPROM Using WinROM to Configure the EEPROM www.ti.com The EEPROM (U3) will need to be reconfigured for ExpressCard-mode operation. See Section 1.5 for an explanation of how to configure the EEPROM. Upon deassertion of PERST the XIO3130 will automatically read data from the EEPROM. This data is used to pre-set vari ...

  • Texas Instruments XIO3130 EVM - page 9

    www.ti.com Using WinROM to Configure the EEPROM Figure 1-11. EEPROM Data To update the entire EEPROM from a .dat file that was provided by TI, right click on the XIO3130 entry (see Figure 1-12 ). Select the option "Program EEPROM Data From File." Figure 1-12. Updating the EEPROM SLLU108 – July 2008 XIO3130 EVM 9 Submit Documentation Fee ...

  • Texas Instruments XIO3130 EVM - page 10

    Using WinROM to Configure the EEPROM www.ti.com A new dialog box appears that allows the user to select which .dat file to use to program the EEPROM (see Figure 1-13 ). Select from one of the three operating modes supplied with the EVM. Figure 1-13. Selecting a .dat File After the Open button has been pressed, a new dialog box opens asking if the u ...

  • Texas Instruments XIO3130 EVM - page 11

    1.6 Using the TopHAT Utility www.ti.com Using the TopHAT Utility Once flashing has completed, the contents of the EEPROM now contains the data from the .dat file. However, this data is not yet present in the PCI configuration space of the XIO3130. Once flashing has finished, WinROM displays a dialog box reminding the user to power cycle the system. ...

  • Texas Instruments XIO3130 EVM - page 12

    Using the TopHAT Utility www.ti.com Figure 1-15. TopHAT 12 XIO3130 EVM SLLU108 – July 2008 Submit Documentation Feedback ...

  • Texas Instruments XIO3130 EVM - page 13

    www.ti.com Using the TopHAT Utility TopHAT parses the PCI configuration space looking for any capability structure. If it finds a capability structure, a new icon and description of the capability will show under the device. For example, under the XIO3130 PCI/PCI bridge (TI) entry, a capability for Power Management Capability Structure is shown wit ...

  • Texas Instruments XIO3130 EVM - page 14

    Trademarks Using the TopHAT Utility www.ti.com Figure 1-17. PCI Registers Any bit in the PCI configuration space can be modified using the PCI Registers dialog box. A new value can be directly typed into the “New Value” edit box or entered by pressing any of the bit numbers below the edit box. The new register value will not be written until th ...

  • Texas Instruments XIO3130 EVM - page 15

    EVALUATION BOARD/KIT IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling th ...

  • Texas Instruments XIO3130 EVM - page 16

    EVM WARNINGS AND RESTRICTIONS It is important to operate this EVM within the input voltage range of 0 V to 3.6 V or –-0.6 V to 0.6 V and the output voltage range of 0 V to 3.6 V or –-0.6 V to 0.6 V. Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the inp ...

  • Texas Instruments XIO3130 EVM - page 17

    IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders ...

Manufacturer Texas Instruments Category Switch

Documents that we receive from a manufacturer of a Texas Instruments XIO3130 EVM can be divided into several groups. They are, among others:
- Texas Instruments technical drawings
- XIO3130 EVM manuals
- Texas Instruments product data sheets
- information booklets
- or energy labels Texas Instruments XIO3130 EVM
All of them are important, but the most important information from the point of view of use of the device are in the user manual Texas Instruments XIO3130 EVM.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Texas Instruments XIO3130 EVM, service manual, brief instructions and user manuals Texas Instruments XIO3130 EVM. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Texas Instruments XIO3130 EVM.

Similar manuals

A complete manual for the device Texas Instruments XIO3130 EVM, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Texas Instruments XIO3130 EVM by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Texas Instruments XIO3130 EVM.

A complete Texas Instruments manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Texas Instruments XIO3130 EVM - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Texas Instruments XIO3130 EVM, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Texas Instruments XIO3130 EVM, that we can find in the current document
3. Tips how to use the basic functions of the device Texas Instruments XIO3130 EVM - which should help us in our first steps of using Texas Instruments XIO3130 EVM
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Texas Instruments XIO3130 EVM
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Texas Instruments XIO3130 EVM in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Texas Instruments XIO3130 EVM?

Use the form below

If you did not solve your problem by using a manual Texas Instruments XIO3130 EVM, ask a question using the form below. If a user had a similar problem with Texas Instruments XIO3130 EVM it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)