English dropdown-ico

Manual Heat Controller R-410A

24 pages 0.75 mb
Download

Go to site of 24

Summary
  • Heat Controller R-410A - page 1

    I N S T A L L A T I O N I N S T R U C T I O N S H I GH - E F F I C I E N C Y CO N D E N S I N G U N I TS F E A T U R IN G E A R T H - F R I E N D L Y R - 41 0 A R E F R I G E R A NT RSG - 6 1 ⁄ 2 & 7 1 ⁄ 2 T ON 92-42665-14-01 SUPERSEDES 92-42665-14-00 W ARNING [ ] INDICATES METRIC CONVERSIONS e a r t h f r i e n d l y r e f r i g e r a n t ...

  • Heat Controller R-410A - page 2

    2 T ABLE OF CONTENTS I .S A F E T YI N F O R M A T I O N ...........................................3 I I . I N T R O D U C T I O N ..................................................4 I I I . C H E C K I N GP R O D U C TR E C E I V E D ...................................4 I V . E Q U I P M E N TP R O T E C T I O N .................................. ...

  • Heat Controller R-410A - page 3

    3 1.0 SAFETY INFORMA TION ! W ARN ING TH IS U NI T MUS T BE P ER MA NEN TL Y GR OUN DE D. A G ROU ND L UG I S PROVIDED NEAR THE CONTACTOR FOR A GROUND WIRE. FAILURE TO D O SO C A N CA U SE A F I RE O R E LE C TR I CA L S HO C K RE S UL T IN G I N PROPERTY DAMAGE, SEVERE PERSONAL INJURY OR DEATH. ! W ARN ING AFTER COMPLETION OF WIRING CHECK ALL ELEC ...

  • Heat Controller R-410A - page 4

    4 II. INTRODUCTION This booklet contains the installation and operating instructions for your self-contained air conditioner. There are a few pre cautions that should be taken to de rive maximum satisfaction from it. Improper installation can result in unsatisfactory operation or danger- ous conditions. Read this booklet and any instructions packag ...

  • Heat Controller R-410A - page 5

    5 V . WHY USE AN AIR COOLED SPLIT SYSTEM? • With an air cooled system, you have no water or sewer connections to make, and no troublesome and costly water treatment problems. • Since the condensing unit is located outside the building, and the low profile air han- dling unit can be installed in the drop ceiling or in the conditioned space, you ...

  • Heat Controller R-410A - page 6

    6 VI. ST ANDARD UNIT FEA TURES — 6 1 ⁄ 2 AND 7 1 ⁄ 2 CABINET — Galvanized steel with a durable powder coat paint finish. The cabinet front and sides are formed into a one piece unitized design with stamped louvers to provide protection for the condenser coils. SERVICE ACCESS — Control box with separation between line and control voltages, ...

  • Heat Controller R-410A - page 7

    TABLE 2 P HYSICAL AND ELECTRICAL DATA TABLE (RSG) 7 Condensing Unit 078 090 Operating Weight (lbs.) [kg] 264 [119.8] 287 [130.2] Shipping Weight (lbs.) [kg] 283 [128.9] 306 [138.8] COMPRESSOR: Quantity 11 Type Scroll RPM 3500 CONDENSER FANS: Quantity 11 CFM [L/s] 4700 [2218] 4700 [2218] Diameter (in.) [mm] 24 [610] 24 [610] Motor Horsepower (ea.) [ ...

  • Heat Controller R-410A - page 8

    8 C. ORDER P ARTS When reporting shortages or damaged parts, or when ordering repair parts, give the c omplete unit model and serial numbers which are stamped on the Unit Rating Plate. D. ST ANDARD ITEMS The condensing unit consists of a completely assembled package which includes a com- p ressor, a condenser coil, fan, fan motors, outdoor control ...

  • Heat Controller R-410A - page 9

    TABLE 3 REFRIGERANT PIPING DATA Equivalent Length (ft.) [m] of straight type “L” tubing for non-ferrous valves and fittings (brazed). Tube Size, O.D. 9 VIII. REFRIGERANT PIPING DA T A CONDE NSING UNI TS ARE SHI PPED WITH A N ITROGE N HOLDING C HARGE. EVACU ATE CONDE NSING UN IT BEFORE C HARGIN G WITH REFR IGERAN T. FIGURE 4 ROOFTOP INSTALLATION ...

  • Heat Controller R-410A - page 10

    10 ! W ARN ING DO NOT U SE OX YGEN T O PUR GE LIN ES OR P RES SURE S YSTE M FOR L E A K T E S T . O X Y G E N R E A C T S V I O L E N T L Y W I T H O I L , W H I C H C A N CAUSE AN EXPLOSION RESULTING IN SEVERE PERSONAL INJURY OR DEATH. FIGURE 5 L IQUID LINE PRESSURE DROP PER 100 FEET EQUIVALENT LENGTH (TYPE L COPPER TUBING) NOTES: 1. When evaporat ...

  • Heat Controller R-410A - page 11

    11 7. Insulate the liquid line whenever the heat pick-up or transfer can affect the sub-cool- ing. 8. Care should be taken to avoid transmission of noise or vibration to building structure. NOTES: 1. The minimum velocity line (700 fpm) is recommended for cooling only units with verti- cal or horizontal run refrigerant lines. 2. For suction pressure ...

  • Heat Controller R-410A - page 12

    12 FIGURE 8 COIL ABOVE CONDENSING UNIT FIGURE 7 COIL BELOW CONDENSING UNIT 16' to 50' 51' to 100' 101' to 150' EQUIVALENT LENGTH TO EVAPORATOR (FEET) 0' to 15' LIQUID LINE O.D. SIZES (INCHES) RECOMMENDED VAPOR AND LIQUID LINE SIZES FOR VARIOUS LENGTHS OF RUN VAPOR LINE O.D. SIZES (INCHES) 078 1 ⁄ 2 1 ⁄ 2 ...

  • Heat Controller R-410A - page 13

    13 VIX. WIRING NOTE: Field wi ring must comply wi th the National Ele ctric Code (CEC in C anada) and any local ordi nance that may app ly. X. ELECTRICAL POWER It is i mpo rtan t tha t pro per el ect ric al pow er is a vai labl e at th e uni t. Vol tag e mus t not va ry mor e tha n 10% of t hat s tam ped on t he ra tin g pla te. (S ee El ect rica l ...

  • Heat Controller R-410A - page 14

    14 XVI. R-410A REFRIGERANT A. TOOLS REQUIRED FOR INST ALLING & SERVICING R-410A MODELS M anifold Sets: -Up to 800 PSIG High Side -Up to 250 PSIG Low Side -550 PSIG Low Side Retard Manifold Hoses: -Service Pressure Rating of 800 PSIG Recovery Cylinders: - 400 PSIG Pressure Rating -Dept. of Transportation 4BA400 or 4BW400 B. SPECIFICA TION OF R-4 ...

  • Heat Controller R-410A - page 15

    D. REPLACEMENT UNITS To prevent failure of a new condensing unit, the existing evaporator tubing system must be correctly sized and cleaned or replaced. Care must be exercised that the expansion device is not plugged. For new and replacement units, a liquid line filter drier should be installed and refrigerant tubing should be properly sized. Test ...

  • Heat Controller R-410A - page 16

    T ABLE 5 16 (1) Wire length equals twice the run distance. FIELD WIRE SIZE FOR 24 VOLT THERMOSTAT CIRCUITS SOLID COPPER WIRE - AWG 3.0 16 14 12 10 10 10 2.5 16 14 12 12 10 10 2.0 18 16 14 12 12 10 50 100 150 200 250 300 Length of Run - Feet (1) Thermostat Load - Amps N OTE: The condensing unit is shipped with a holding charge of dry nitrogen which ...

  • Heat Controller R-410A - page 17

    17 15. Note weight of refrigerant tank. 16. When system has stabilized, check superheat at the suction line service valve. The actual line temperature should be 15° to 25°F higher than the saturation temperature corresponding to the suction pressure. If superheat is measured at evaporator, the actual line temperature should be 15° to 20° higher ...

  • Heat Controller R-410A - page 18

    18 B. LIQUID PRESSURE CONTROL Outdoor fan motor speed control designed to regulate condenser head pressure at low ambients by varying the air volume through the condenser. Has been tested and is avail- able through the parts department. C. LIQUID LINE SOLENOID V AL VE LIQUID LINE SOLENOID VALVE (24V) — Recommended for all split system applica- ti ...

  • Heat Controller R-410A - page 19

    19 RSG078 SYSTEM CHARGE CHAR T 6 1 ⁄ 2 T ON CONDENSER Pressure at Liquid Service P ort (psig) Pressure at Suction Service P ort (psig) 6-1/2 T ON CONDENSING UNIT 60HZ. REFRIGERANT R-410A 92-102644-01-01 CA UTION: BEFORE FINAL REFRIGERANT CHECK, INDOOR AIR TEMPERA TURE SHOULD BE A T COMFORT CONDITIONS FOR MOST ACCURA TE RESUL TS. INSTRUCTIONS: 1. ...

  • Heat Controller R-410A - page 20

    20 Pressure at Liquid Service P ort (psig) Pressure at Suction Service P ort (psig) Outdoor Ambient (F° DB) 7-1/2 T ON CONDENSING UNIT 60HZ. R EFRIGERANT R-410A 92-102644-03-01 CA UTION: BEFORE FINAL REFRIGERANT CHECK, INDOOR AIR TEMPERATURE SHOULD BE AT COMFORT CONDITIONS FOR MOST ACCURA TE RESUL TS. INSTRUCTIONS: 1. CONNECT PRESSURE GUAGES TO SU ...

  • Heat Controller R-410A - page 21

    21 B. MAINTENANCE AND OPERA TION 1. All access panels must be in place when unit is in operation. 2. For maximum efficiency, the condenser coil must be kept clean. Periodic inspections, depending on local conditions are recommended. If it is necessary to clean the con- denser coil, use a common garden hose. 3. Never operate the unit without filters ...

  • Heat Controller R-410A - page 22

    22 W ARNING ! DISCONNECT ALL POWER TO UNIT BEFORE SERVICING. CONTACTOR MAY BREAK ONLY ONE SIDE. FAILURE TO SHUT OFF POWER CAN CAUSE ELECTRICAL SHOCK RESULTING IN PERSONAL INJURY OR DEATH. SYMPTOM POSSIBLE CAUSE REMEDY Unit will not run • Power off or loose electrical connection • Check for correct voltage at compressor contactor in control box ...

  • Heat Controller R-410A - page 23

    23 ...

  • Heat Controller R-410A - page 24

    24 CM 1208 ...

Manufacturer Heat Controller Category Air Conditioner

Documents that we receive from a manufacturer of a Heat Controller R-410A can be divided into several groups. They are, among others:
- Heat Controller technical drawings
- R-410A manuals
- Heat Controller product data sheets
- information booklets
- or energy labels Heat Controller R-410A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Heat Controller R-410A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Heat Controller R-410A, service manual, brief instructions and user manuals Heat Controller R-410A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Heat Controller R-410A.

Similar manuals

A complete manual for the device Heat Controller R-410A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Heat Controller R-410A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Heat Controller R-410A.

A complete Heat Controller manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Heat Controller R-410A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Heat Controller R-410A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Heat Controller R-410A, that we can find in the current document
3. Tips how to use the basic functions of the device Heat Controller R-410A - which should help us in our first steps of using Heat Controller R-410A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Heat Controller R-410A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Heat Controller R-410A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Heat Controller R-410A?

Use the form below

If you did not solve your problem by using a manual Heat Controller R-410A, ask a question using the form below. If a user had a similar problem with Heat Controller R-410A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)